JBS07PIY2 General Electric Range - Instructions

(Turn off the Power) Pull stove out, remove the 2 screws that holds switch in place, remove one wire at a time and install on new switch. Slip switch in replace 2 screws. Snap off about 3/4 of the shaft cut down plastic insert for knob, install knob turn on power and it works.

Remove center cover on back of stove exposing wiring. Unplug stove from 220v outlet. Unplug wires from old element.From inside stove, Remove 4,quarter inch screws holding back panel inside oven in place. Remove back panel from inside oven. Will be able to see the brackett on element and 2 screws holding the element/brackett in place, rem ... Read more ove those 2 screws and remove old element. Reverse process to install new element.

slid the range away from wall. disconnect power. removed back,compared switches and marked wires.installed new switch and wires.the adapter for the control knob was a problem it left the knob out futher than original i had to modify the plastic adapter and got it close enought! the most time spent was cleaning up the floor before putting ... Read more the range back.

I read parts select instructions and i was done in less than 30 minutes. Since 1988, this is the 1st. part that I had to replace. I now have parts select on my favorites list.

The only problem was m short arm and no good flash lights around

I unplugged th oven, for my safety. Removed 2 small bolt head screws, unplugged 2 wire connecters similar to car speakers connecters. Removed the element. Then took a few minutes to clean bottom of oven. It is so much easier with out the element. I plugged the wires onto new element, then i put the 2 small screws back in. Plugged in oven, ... Read more pushed it back in place and turned on oven. It has been great! I think old element was unevenly heating. Baking has been noticable better. Thank you partselect.com. a very satisfied New England customer

Removed two screws, pulled old element forward 2 inches, removed two wires. Pulled old element out of oven. Put new element in oven, attached two wires, pushed element all the way in, put two screws in and tightened them. Turned oven on to test new element. Element worked. Project completed.

It took longer to get the new element out of the box than it did to install it. I removed the two screws with a 1/4" nutdriver, pulled the element out roughly three inches, unplugged the connectors and discarded the old element. I did the reverse to install the new element.

Removed old; inserted new.

I took a chance and guessed that the problem was the element, as opposed to a thermostat or other part that may have failed. (Oven was made in the 70's) I entered the data for this old oven on the PartSelect.com website and it came up with a part for me to order. When I received the replacement element, I noticed that it was not "exact ... Read more ly" the same shape as the old part, but the dimensions were correct and it fit into the space on the bottom of the oven without any problems. The dimensions of the connectors were pretty close to exactly the same as the old element, and the screw holes in the mounting plate lined up perfectly with the corresponding threaded holes in the back wall of the oven - it took me less than 15 minutes to install the part and the oven appears to be working perfectly again.

unplugged the broken elements and plugged in the new ones. Took about one minute. Tools used: hands and fingers.

already had the old one disconnected (spade ends) on old element, new one arrived installed it the same way I removed the old part, just 2 little screws to hold it in place, after you reconnect the spade ends. Then plugged the unit back in. Always use common sense when working with electrical appliances! Easy as the pie I can now bake.

The repair went very smooth and easy it took me around 10 minutes to replace part and I was ready to bake again

I removed the burners, took the old drip pans out, put the new ones in and put the burners back in. This was so easy that a caveman could do it.

It wasn't so much the repair that was needed as how impressed I was with the fast delivery. Without a fourth burner & a holiday weekend coming up I was in desperate need of my element. I ordered it around 1:00 pm on a friday & it was delivered the next day before noon! Very impressed with the ease of ordering & receiving. Thanks again.