JBS034F2 General Electric Range - Instructions

remove screws attaching burner plate to back of oven, pull out element, undo wiring to old burner by unscrewing 2 screws, remove old burner, reverse process to put new burner in

First observed the situation to determine if I should try and repair. I decided I could and should. Got the element and proceeded. I first turned the power off at the circuit breaker to cut the electrical power to the stove then I removed the two screws that holds the unit in place and then pulled unit out to where I could see the wire co ... Read more nnection; removed the two screws on the wire connection and replaced the old element with the new element. reinserted the unit back into position and replaced the two screws that holds the unit in the stove. Turned power back on and tested the oven for any problems. Stove is working great.

TURN OFF CIRCUIT BREAKER before doing anything even if oven is not turned on! If I hadn't checked voltage with tester before starting I would have made a shocking discovery.
1) unscrewed shield cover to get get at the element screws.
2) unscrewed element screws and removed old element - pulling connecting wires out about 3 inch ... Read more es
3)attached new element to connecting wires (2 screws)
4) pushed new element into place and reattached element connector plate to wall of oven
5) reattached shield cover to wall of oven

First I turned the Breaker off for the Oven. I removed the two screws that hold the element/cover plate. I pulled the element out to get access to wires attached to element & removed screws holding wires to element. I reversed the process to put back together.

The repair was fairly easy. Removed the 2 screws that hold the plate to the oven and then pulled out the element and loosen up the screws that connect it. Installed the new element and re-attached the element to the plate and secured the plate back to the oven. This site was very easy to use and very helpful and I will use it again if I n ... Read more eed another part.

1. Removed the old element. Had a little trouble loosening the screws. After we got them loose, everything was easy.
2. Pulled out the element and disconnected the wires.
3. Connected the wires on the new element.
4. Screwed the element back in.
5. Connected the stove and turned on the oven.
6. It works like a ne ... Read more w one.

Unplugged stove, removed front door, carefully removed two screws holding the cover plate of the element. Gently pulled the element out about 3-4 inches removed the two screw attaching the electrical wires to the element , making sure the wires did not pull back into the stove. Removed old element, attached new element to the electrical ... Read more wires with the new screws received with the new element. Carefully pushed the wires and element back into place making sure the insulation was also in place. Re-attached the cover plate with the two screws I had removed. Plugged the stove back in and tested the element. Replaced the front door .... job complete!

Just wanted to add that the part came in two days, super mailing time, thanks!!

The element was 25 years old and I was concerned about changing it. But is was so easy. I turned off power and removed 2 screws and then unscrewed the wiring from the old element. I had the new one installed in minutes. I was so glad to have my oven working again. Who needs a man.

First shut off power to the range in the electrical
breaker box (its the 220 breaker) as marked.
Remove the oven door ( open part way and lift up) the
door will come off.
Remove the 2 screws that the element is attached to the
back of the oven wall. Pull element out part way and
disconnect the 2 ... Read more wires. Take out element.
The new element had different connections so I cut off
the clips stripped the wires and attached to the element
connection . The element had connections that this was
possible. Push wires back into oven wall and install the
new element with the 2 screws that were removed. You
could also put on clips to the 2 wires that attach to the
element if so desired. (Eye hole clips.)

My husband first turned the main breaker off to the stove. Pulled the stove away from wall, took off the back plate, unhooked the element and out the new one in!!

Turned off power. Removed old broken one installed new one in minutes. Turned power on and tested it out. If this 60 something lady can do it, you can too.

Identify oven breaker and turn off power before starting. Opened oven door. Removed oven racks. Use 1/4" socket or nut driver to remove the 2 bolts holding heating element mounting bracket at rear base of oven. Carefully pull element out of installation mount to remove the 2 machine screws that attach electrical wires to the heating eleme ... Read more nt. Reattach wires in same order as original element. Then reinstall new element in reverse order of removal. Took all of maybe 15 minutes! Excellent OEM Parts!

Flip the circuit breaker going to oven off, then used a 1/4 inch socket on the mounting flange bolts and the bolt head screws attaching the wires. Then used a flat head screwdriver to reattach the wires with the supplied screws and bolted the new element in place. Back to the circuit breaker flipped the switch and turned the oven on to te ... Read more st it, and now works fine. *be sure to remove the sticker before installation, use rubbing alcohol to remove any residue.*

Snapped in place (4)

1. Turn off power to range and remove element.
2. Remove clips from ceramic guards.
3. Disconnect wiring.
4. Connect wires to new element.
5. Install ceramic guards and clips
6. Attached element to range.
7. Restore power.