JBS033P1 General Electric Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Worn out burner element
1 person
found this instruction helpful.
-
Art from SEATTLE, WA
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
1. Turn off power to range and remove element.
2. Remove clips from ceramic guards.
3. Disconnect wiring.
4. Connect wires to new element.
5. Install ceramic guards and clips
6. Attached element to range.
7. Restore power.
2. Remove clips from ceramic guards.
3. Disconnect wiring.
4. Connect wires to new element.
5. Install ceramic guards and clips
6. Attached element to range.
7. Restore power.
Was this helpful?
Thank you for voting!
bake element no heat
1 person
found this instruction helpful.
-
larry from buckhannon, WV
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers
took old element out , put new element in.very easy.
Was this helpful?
Thank you for voting!
bottom drawer guides
1 person
found this instruction helpful.
-
Jim from TRAVERSE CITY, MI
- Very Easy
- Less than 15 mins
-
Pliers
Snapped in place (4)
Was this helpful?
Thank you for voting!
Really old range. Broken bake element in oven.
1 person
found this instruction helpful.
-
Kathleen from Grand Rapids, MI
- Very Easy
- Less than 15 mins
Turned off power. Removed old broken one installed new one in minutes. Turned power on and tested it out. If this 60 something lady can do it, you can too.
Was this helpful?
Thank you for voting!
Element burned out
1 person
found this instruction helpful.
-
Wendy from CHESHIRE, CT
- Really Easy
- 15 - 30 mins
-
Socket set
My husband first turned the main breaker off to the stove. Pulled the stove away from wall, took off the back plate, unhooked the element and out the new one in!!
Was this helpful?
Thank you for voting!
No heat from bake element
1 person
found this instruction helpful.
-
Roberta from Southampton, NJ
- Really Easy
- Less than 15 mins
-
Socket set
Ordered part, took old bake element out, installed new bake element. It was real easy.
Was this helpful?
Thank you for voting!
Bake element burned out
1 person
found this instruction helpful.
-
Lavona from JACKSONVILLE, FL
- Very Easy
- Less than 15 mins
-
Screw drivers, Socket set
Flip the circuit breaker going to oven off, then used a 1/4 inch socket on the mounting flange bolts and the bolt head screws attaching the wires. Then used a flat head screwdriver to reattach the wires with the supplied screws and bolted the new element in place. Back to the circuit breaker flipped the switch and turned the oven on to te
... Read more
st it, and now works fine. *be sure to remove the sticker before installation, use rubbing alcohol to remove any residue.*
Read less
Was this helpful?
Thank you for voting!
No problems
1 person
found this instruction helpful.
-
Darlene from NORTH AUGUSTA, SC
- Really Easy
- Less than 15 mins
lift eye slide in bowl and trim ring, put the eye back down,
Other Parts Used:
Was this helpful?
Thank you for voting!
Bottom oven heating element was out
1 person
found this instruction helpful.
-
John from FALL RIVER, MA
- Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
Very easy repair. 2 hex head screws to take the heating element out. Then 2 more slot head screws for the wire connections. Perfect fit and operation of the new heating element.
Was this helpful?
Thank you for voting!
Bottom Bake Element had burnt into/split
1 person
found this instruction helpful.
-
Miranda from UNION GROVE, NC
- Really Easy
- Less than 15 mins
-
Socket set
Very easy and simple/ After making sure power supply was off, removed socket screws in back plate of element, slid old element out, attached new element and replaced/tightened socket screws on plate and new element. Power on, oven on .. heated quickly and nicely. Used oven several times since ... no problems.
Was this helpful?
Thank you for voting!
elememt not working
1 person
found this instruction helpful.
-
ROBERT from ORWELL, VT
- Really Easy
- 30 - 60 mins
-
Screw drivers
Hi, First unplug appliance ,remove the oven door by pulling it up from the hinges, giving room to work deep inside , remove the two screws that hold the element in place. then pull the element out carefully not to stress the wires and replace the element . Note after all is done test with an oven thermometor :)
Was this helpful?
Thank you for voting!
All burners on stove needed to be replaced due to age
2 of 4 people
found this instruction helpful.
-
ROY from CULPEPER, VA
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
Followed instruction that came in the new parts. Each element took about 10 minutes to remove, inspect the wires, clean the connections and reconnect the new elements. The element covers that came with the kit were easy to install, and everything fit just fine. Most important thing is to turn of the electrical power to the unit BEFORE
... Read more
you start.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
The bottom bake element burned out.
1 person
found this instruction helpful.
-
Pauline from DECATUR, GA
- Really Easy
- 30 - 60 mins
-
Screw drivers
1. Cut power off. 2. Remove old element, make sure you do not lose the screws, pull the connecting posts out and we used strings on posts so they could not get lost in the wall. 3. We then replaced the new element with little of no problems, it took approximately 30-45 minutes for the whole process.
Was this helpful?
Thank you for voting!
When moving the range, the 220 wire popped off the terminal and arced melting the plastic terminal
1 person
found this instruction helpful.
-
Randall from ST PETERSBURG, FL
- Difficult
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
I looked for a new terminal locally, but no one had s terminal that would fit a 40-year old range. I went on line to PartSelect and could not find my model range, so I looked through all the terminals listed on the website (about 500) but found only one that was close to mine. Mounting holes did not match, but it had 3 connectors with 2
... Read more
20 capability, so I ordered it. I requested express shipping by UPS and thought I paid for the extra charge. When I got notification of shipment. I saw it was via ground. It went from Louisville to Jacksonville to Clearwater, FL. I ordered it on Thursday night and received it the following Tuesday night. Meanwhile, we had no stove to cook on. When the part came, it took two days to get the contractor back to our condo. He drilled new holes on the mounting box and jerry-rigged the wiring to make it fit. The range is now working, but I was disappointed in the delay in shipping which I agreed to express shipping.
Read less
Was this helpful?
Thank you for voting!
Broiler and Baking elements replacement
1 person
found this instruction helpful.
-
Joseph from Buford, GA
- A Bit Difficult
- 1- 2 hours
-
Pliers, Screw drivers
Unplug range from its 220V source. Make sure range is not hot from recent usage. You’ll need a #2 Philips driver, preferably one with 14-18 inch length. The old screws will likely be very stubborn about coming loose. Two of them hold bottom element in. Remove the back panel so access to the two connectors on the bottom element are easily
... Read more
removable. Be very careful not to the let the wire connectors from the heating element drop down into the insulation. For the top element, there are four screws holding it in place, I found it was easier to access these two screws leaning the range backward at a slight angle. Take special care again not to let the wires drop down into the insulation. The connectors to the old element will likely need some extra effort to remove. The reconnection to the new elements should be ok. Make sure all screws go back in that were removed. The new elements will be amazing, and baking and broiling will be like new again.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!