J508R2 General Electric Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
bottom heating element replaced
1 of 2 people
found this instruction helpful.
-
David from Dallas, TX
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
First I removed the two screws that hold the element in place. I then pulled the element out about 2 inches and disconnected the two wires.
I reconnected the two wires to the new element and screwed the new element to the wall of the oven where the element was held in place.
I reconnected the two wires to the new element and screwed the new element to the wall of the oven where the element was held in place.
Was this helpful?
Thank you for voting!
The bake element had cracks in it and was almost burned through in a couple of spots.
1 of 2 people
found this instruction helpful.
-
George from Otsego, MI
- Really Easy
- Less than 15 mins
-
Nutdriver
I ordered the bake element on Monday and received it on Wednesday. Great delivery.
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...
Then I installed the new element using the steps above in reverse. Very clean and simple. One tip t ... Read more hough...open your oven door slightly to the detent and pull straight up. The door slips off easily and allows easy access to the bake element screws.
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...
Then I installed the new element using the steps above in reverse. Very clean and simple. One tip t ... Read more hough...open your oven door slightly to the detent and pull straight up. The door slips off easily and allows easy access to the bake element screws.
Read less
Was this helpful?
Thank you for voting!
heating element not working
1 of 2 people
found this instruction helpful.
-
JOHN from GREENE, RI
- Really Easy
- Less than 15 mins
-
Nutdriver
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I reattached them to the new element screwed it back in place and I was done. Could not have been easier! Getting the right replacement part the next day after placing the order was a pleasant surpri
... Read more
se. This is the second time I used your company and I am very impressed with your service. I recommend you to everyone I can. Great Job!
Read less
Was this helpful?
Thank you for voting!
Vintage Oven Element stp working
1 of 2 people
found this instruction helpful.
-
Steven from Cerritos, CA
- Really Easy
- Less than 15 mins
-
Pliers, Wrench set
Tried contacting GE and no luck, they did not have vintage parts. After searching and locating Partselect, I was able to see a pic of the actual replacement part. I wasn't sure about purchasing online (1st timer) but decided to go for it!
I was able to track the package, although FedEX was setup to deliver to my resdient, I had ... Read more the package addressed to my office but we worked that out also and walla.
I was very please and now I can bake my famous Pot Roast again. The oven was not working for 8 mos.
Good Eaten!
SJ-Long Beach CA
I was able to track the package, although FedEX was setup to deliver to my resdient, I had ... Read more the package addressed to my office but we worked that out also and walla.
I was very please and now I can bake my famous Pot Roast again. The oven was not working for 8 mos.
Good Eaten!
SJ-Long Beach CA
Read less
Was this helpful?
Thank you for voting!
The bake element actually melted and broke into pieces
1 of 2 people
found this instruction helpful.
-
Victor from Waynesboro, PA
- Easy
- Less than 15 mins
-
Nutdriver, Pliers, Screw drivers
It was realatively simple, turned off the power to the oven, removed the bake element , by loosening the two metal screws in the back of the oven, with a nut driver and removing the screws, then pulling the element outward, to expose the two wires ,that were connected to the element, using a nut driver to remove the two screws and a pai
... Read more
r of pliers to hold the wire connectors, then removed the old element. Installed the new bake element, by connecting the two wires to the element, with the two screws, then pushing the element back in place , attaching the element to the back of the oven, with the two metal screws, finished with the installation, turned power back to the oven , and tested to make sure the oven worked , all done.
Read less
Was this helpful?
Thank you for voting!
bottom didn't heat.
1 of 2 people
found this instruction helpful.
-
rhonda from mauston, WI
- Really Easy
- Less than 15 mins
-
Screw drivers, Wrench set
First removed screws then removed burned out element.Replaced with new element and replaced screws and cooked pizza.
Was this helpful?
Thank you for voting!
oven barely heated/no heat
1 of 2 people
found this instruction helpful.
-
Pearl from Bay City, TX
- Really Easy
- 15 - 30 mins
-
Nutdriver
The delivery of the part was within 3 days.I only had to connect the two screws had biscuits that night.
Was this helpful?
Thank you for voting!
Bottom "Bake" Element not working - Broken in half
1 of 2 people
found this instruction helpful.
-
Lynn from Apex, NC
- Really Easy
- Less than 15 mins
-
Nutdriver
Removed 2 mounting screws - Removed 2 screws used to attach wiring to element. Received new element and re-attached the 4 screws.
Was this helpful?
Thank you for voting!
Bake Element Broke due to age
1 of 2 people
found this instruction helpful.
-
Kevin from Centerville, OH
- Easy
- 15 - 30 mins
-
Nutdriver
Repair was easy.
Note: the element leads have a potential across them,
so unplug the unit or you'll have an arc strike.
I liked the selection method at PartsSelect.com.
Finding the replacement part was easy from the pictures.
The prices were reasonable.
The part came next day, which was a surprise ... Read more .
Removal and Installation was 4 screws.
I have become a DIY hero.
Only downside was going out for dinner every night ended.
This site is now a Favorite.
Note: the element leads have a potential across them,
so unplug the unit or you'll have an arc strike.
I liked the selection method at PartsSelect.com.
Finding the replacement part was easy from the pictures.
The prices were reasonable.
The part came next day, which was a surprise ... Read more .
Removal and Installation was 4 screws.
I have become a DIY hero.
Only downside was going out for dinner every night ended.
This site is now a Favorite.
Read less
Was this helpful?
Thank you for voting!
Door seal had large pieces missing
1 of 2 people
found this instruction helpful.
-
David from BROOKLYN, MI
- Difficult
- More than 2 hours
-
Nutdriver, Screw drivers, Socket set
I had to remove the door, burners, stove cooktop, both oven heating elements. Two j bolts in the rear of range hold oven box to range body and sandwich the seal in place. After removing the oven box the new seal could be installed, then reassemble everything.
Was this helpful?
Thank you for voting!
The Bottom Bake Element had burned out and would not heat
0 of 1 people
found this instruction helpful.
-
Stanley from Inman, SC
- Really Easy
- 15 - 30 mins
-
Socket set
First I turned off the breaker to the stove in the breaker box and then removed the two small screws that hold the element in place. I then carefully pulled the element out about 3 inches and using a 1/4 inch socket, I unscrewed the screws that held the wire on the bake element. There were two wires held in place with 2 small screws.
... Read more
I made sure that when I unhooked the wires they did not pull back into the back wall of the stove. I then removed the old element and put the new one in its place, hooked the two wires back up, pushed it back in place and secured it to the back of the wall of the stove with the other two screws. I then turned the power back on and presto, it worked perfectly. Like new again.
Thanks for everything.
Thanks for everything.
Read less
Was this helpful?
Thank you for voting!
replaced element
0 of 1 people
found this instruction helpful.
-
carey from granbury, TX
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers
(e.g. First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...)
Was this helpful?
Thank you for voting!
The bake element 'fried itself'' -- making a horrible electrical noise and flaring up -- before dying.
0 of 1 people
found this instruction helpful.
-
Jeanne M. from Oreland, PA
- Really Easy
- 15 - 30 mins
-
Screw drivers, Socket set
First -- and thank goodness I read some of these stories first or I would have forgotten -- I turned off the circuit breaker to the stove.
I removed the two nut screws holding the element itself to the back of the over. Then I removed two more nut screws holding the element to the electrical wires. (This took some WD-40. The s ... Read more tove is about 25 years old.)
That was about it. Everything lined up perfectly, and there was nothing more to do except reconnect the new element and throw the breaker back on. It works!
I removed the two nut screws holding the element itself to the back of the over. Then I removed two more nut screws holding the element to the electrical wires. (This took some WD-40. The s ... Read more tove is about 25 years old.)
That was about it. Everything lined up perfectly, and there was nothing more to do except reconnect the new element and throw the breaker back on. It works!
Read less
Was this helpful?
Thank you for voting!
Lower Baking element stopped heating after a 1" section melted and burned at a bend.
0 of 1 people
found this instruction helpful.
-
Richard from Ellisville, MO
- A Bit Difficult
- 15 - 30 mins
-
Screw drivers, Socket set
I removed both screws to remove lower element, and measured it prior to ordering the replacement.
Then in a few days it arrived, and I installed it. The new element had small bolts rather than screws the original used to attach both wires. A flashlight was necessary in locating an keeping an eye on the wire ends, to keep them fr ... Read more om being pulled inside the back cover, as the bolts were attached.
Then in a few days it arrived, and I installed it. The new element had small bolts rather than screws the original used to attach both wires. A flashlight was necessary in locating an keeping an eye on the wire ends, to keep them fr ... Read more om being pulled inside the back cover, as the bolts were attached.
Read less
Was this helpful?
Thank you for voting!
bottom heating element broken
0 of 1 people
found this instruction helpful.
-
sharon from mt pleasant, NC
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
I was a little leary of using a website to order a part to fix my oven, but we got the part within a week. It was very easy to install and it works like a charm!
Was this helpful?
Thank you for voting!