EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

J438B3 General Electric Range - Instructions

All Instructions for the J438B3
16 - 30 of 78

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Broiler unit burned out
3 of 5 people found this instruction helpful.
  • Phillip from Charlotte, NC
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver
I removed the unit easily with anut driver, however the unit also supported the thermo-link. I had to use the hack saw to relieve a small opening for the thermo-link to pass through. No real problem. Then a few holes to be drilled to attach the 'link' to the base of the broiler unit.

BUT-I went into the website listed on the bo x. GEAppliances.com Guess what? Their price was twice yours!!
Was this helpful?
Thank you for voting!
Replaced old burners
3 of 5 people found this instruction helpful.
  • Terry from Ulen, MN
  • Easy
  • 1- 2 hours
  • Pliers, Screw drivers
Both the eight inch burner and the the six inch burner were not an exact fit. I used the old rings and the new burners. The eight inch burner fit well with the new drip bowl;however, the six inch burner did not fit with the six inch drip bowl and I had to grind off about an eigth inch from the diamiter of the drip bowl. I replaced most al l the wiriing and after I get the lower oven element rebuilt it will be ready for a test drive ..can't wait!
Was this helpful?
Thank you for voting!
Broiler element stopped heating
3 of 5 people found this instruction helpful.
  • Steve from Fort Worth, TX
  • A Bit Difficult
  • 1- 2 hours
  • Screw drivers
Broiler element arrived at my door 3 days after ordering which was nice. Apparently the billing dept. is out of the USA so don't be surprised, like I was, to find a suspicious looking charge for a currency exchange fee (mine was 42 cents). I had to drill two new screw holes in the base of the new element in order for it to fit my oven. I also had to use heavy wire snips to cut off about an inch of the top of the new element base. The female electrical connections also had to be spread out with needle nose pliers since the new element connections were slightly thicker. With all of the issues I had I was frustrated and it took about two hours. On the other hand, the part works perfectly and was priced right. Hopefully it will fit perfectly out of the box for your oven.
Was this helpful?
Thank you for voting!
broiler element was broken
2 of 2 people found this instruction helpful.
  • Milli from AURORA, CO
  • Difficult
  • More than 2 hours
  • Pliers, Screw drivers, Socket set
I looked on Youtube for a how to video. It was accurate but the screws in my oven were NOT phillips head screws, they turned out to be sheet metal screws. I used pliers at first which was a PAIN but then I borrowed a socket wrench from the neighbor that was MUCH better!! I had wanted to do it myself to prove to my husband and son that I c ould but I ended up needing their help because the screws were so tight.... But we did the repair ourselves!!!
Was this helpful?
Thank you for voting!
Burner element damaged and needed replacement.
2 of 3 people found this instruction helpful.
  • Donald from Holmdel, NJ
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
This part has the trim ring attached. My old element had the trim rim detached. This new part still fit my stove top and works fine.
Was this helpful?
Thank you for voting!
Burner was out
1 person found this instruction helpful.
  • Gerald from Lakeland, FL
  • Really Easy
  • Less than 15 mins
  • Screw drivers
First I removed the screw that holds the element in place. I then pulled the element out about 3 inches and disconnected the three wires. Then I just had to do it in reverse. EASY!
Was this helpful?
Thank you for voting!
Oven wouldn't heat
2 of 4 people found this instruction helpful.
  • Peter from Sacramento, CA
  • Really Easy
  • Less than 15 mins
  • Nutdriver
First I shut off the circuit breaker for the oven then removed the screws that hold the element in place. The element was pulled out about 3 inches and unscrewed the 2 screws to disconnect the two wires. Upon receipt of the new element, I simply reversed the above process and the oven performed like new. Very easy, very quick and very grateful to have the oven operating again and it was a very inexpensive fix.
Was this helpful?
Thank you for voting!
Replaced hinge mounted burner
1 person found this instruction helpful.
  • LUISA from EDEN, NC
  • A Bit Difficult
  • 1- 2 hours
  • Nutdriver, Screw drivers
Parts arrived bent and element had tape residue on it. After approximately 1 hr. I was able to clean, make parts straight and install it.
Was this helpful?
Thank you for voting!
Replace cracked broiler element
1 of 2 people found this instruction helpful.
  • Deborah from Middletown, CT
  • Easy
  • 30 - 60 mins
  • Screw drivers, Wrench set
Unplugged Stove, pulled away from wall. With smaller wrenches, took the two screw-nuts off the inside back and above that hold the broiler element in place. Since it is an older stove...took the back panel off the stove with philips screw-driver which consisted of 10 screws. Once that was removed was able to unscrew the broiler element fr om the two wires that provide the electricity. Used the flash light when I had to unfasten the screw-nuts inside the stove because kitchen lighting wasn't strong enough.
Was this helpful?
Thank you for voting!
burned-out broiler element
2 of 5 people found this instruction helpful.
  • William from Carmel, NY
  • Easy
  • 1- 2 hours
  • Nutdriver, Pliers, Screw drivers
turn off breaker in electrical panel....remove stove socket from outlet....remove rear panel from stove....undo wire connectios from broiler element....inside the oven, gently move thermostat wire out of the way....unbolt broiler plate from rear wall....remove broiler hanger and then broiler element....reverse procedure and you're all set .
Was this helpful?
Thank you for voting!
Broken broiler element
1 of 2 people found this instruction helpful.
  • Michael from Medford, NY
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
Replacing the part was fairly simple. Do not forget to dis-connect the element from the back.
Was this helpful?
Thank you for voting!
Old surface burner burned out one of its two circuits.
1 of 2 people found this instruction helpful.
  • James from Houston, TX
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
I unscrewed the old burner from the stove, took off the three wire to the heating element marking down where each colored wire went, taped off the exposed wires, ordered the new burner, and waited for it to arrive. When it got here, I installed it, and believe it or not, the new burner works just fine!. End of exciting repair story.
Was this helpful?
Thank you for voting!
Broiler element burned out
1 of 2 people found this instruction helpful.
  • Alyce from Littleton, CO
  • Really Easy
  • Less than 15 mins
  • Nutdriver
The customer service at PartSelect.com is wonderful. They assisted me to located a part for a 40 year old oven. Took only a few minutes to take the old one out and put the new one in. Process was pretty self explanitory.
Was this helpful?
Thank you for voting!
broiler element not coming on
1 of 2 people found this instruction helpful.
  • Michele from Roanoke, TX
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
removed 2 nuts holding the element in the oven. removed 2 screws that secured the wires to the element. installed the new element in reverse.
Was this helpful?
Thank you for voting!
burner started sparking and burned right through the coil
1 of 3 people found this instruction helpful.
  • Nancy from Houston, TX
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Took the old part off and marked the wiring for easy replacing and looked all over town and no part to match, so I went to the Internet and put in 8" burner and luckily found your website. The part was perfect and saved me alot of time doing more research for the part. Thank you for the quick shipment and good correspondence.
... Read more >I will definitely use you again for parts and tell my friends about your website too.
Was this helpful?
Thank you for voting!
All Instructions for the J438B3
16 - 30 of 78