J438B2 General Electric Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Replaced Oven Broiler Element
0 of 2 people
found this instruction helpful.
-
Bill from Langhorne, PA
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Removed old, burned out element, and replaced with a new element. The worst part of the entire job was getting the oven door assembled back on to the oven.
Was this helpful?
Thank you for voting!
The broiler element burned out
0 of 3 people
found this instruction helpful.
-
Lana from Elgin, OK
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
First my husband removed the screws that held the element in place, pulled it partially out and then disconneted the wires. He located the part number that was stampted on the defective element and then I searched the internet for GE parts. I noted the price at GE site and continuted to search. The PartSelect price was about 1/2 of the
... Read more
GE price. We ordered the part, it arrived in two days, and we replaced it in less than 30 minutes. We were very pleased.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Broiler element burned out
-
Glenn from Old Saybrook, CT
- A Bit Difficult
- 1- 2 hours
-
Nutdriver, Screw drivers, Socket set
Repair is pretty easy, its the accessability that makes it difficult. This is a wall mount oven. Removing the door would provide pretty good access, but having to reach over the door into the very top back of the oven is a real pain (in the back and other places). As another customer said, there were many dropped screws and much cussin
... Read more
g. The old element terminals were just holes in a metal tab that accepted tapered screws. The new element had terminals that were threaded to accept the screws provided. It took lots of twisting and turning of the element and the power wiring to get the terminal on the wire lined up with the terminal on the element in a position where I could hold them together and insert the screw and start the threads. Don't try this after you've had a beer or two. Whew!!! Many tries, sore back, but did it. Like I said, simple except for the reach. Bake element was much easier. Hope I don't have to do this one again. My GE oven is a winner (20 plus years old) and Parts Select has what you need at a reasonable price and ships quickly. Have used before and will use again, if needed.
Read less
Was this helpful?
Thank you for voting!
broiler element was broken
-
Virginia from Carmel, CA
- Really Easy
- 30 - 60 mins
-
Screw drivers
Asked a local repairman to fix it. I saved money(saved $20.00) by ordering the broiler element from GE part select via customer service agent. The agent was informative and helpful. The part arrived the next day even with regular shipping cost. Impressed with the GE part select. Will use the company again.
Was this helpful?
Thank you for voting!
Our broiler element wasn't working.
-
Donna from Novi, MI
- Difficult
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
We unscrewed the element easily enough, but had a hard time disconnecting the prongs. Once we did, we had to use a thin screwdriver to open the clamps to fit the new prongs into them. After all was accomplished and we switched on the breaker the broiler still didn't work. Either we did something wrong or the element wasn't the problem.
... Read more
We haven't decided our next move yet; whether to get a repairman in or buy a new oven. It's a pretty old oven/range.
Read less
Was this helpful?
Thank you for voting!
Getting in the right position to do the job.
-
Joe from Fort Worth, TX
- Really Easy
- 30 - 60 mins
-
Screw drivers
I am left handed which sometime presents things in a aweward way. My greatest task was finding the right position and being able to hold the leads while trying to connect them. So I got a pillow and positioned myself and got into the oven and was able to do the job from there. After doing so, it took about 10 minutes to do the replacement
... Read more
.
Read less
Was this helpful?
Thank you for voting!
Burnt out broiler element in oven
-
Ronald from Silver Spring, MD
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers, Socket set
Broiler element failed catastrophically (with light flashes) while in use (1986 GE self-clean oven/four burner stovetop). Part number embossed on element plate - very difficult to see - took digital photo while still in oven and magnified. Easy to search for part. Good price, prompt delivery. Removal of old and install new awkward bec
... Read more
ause of access angle and my decreasing nimbleness, as well as oven control thermocouple and support bracket in way. But no technical difficulties. Hex head metal screws holding in element; Notched phillips metal screws holding bracing bracket (easier to put element in by removing one side of bracket). Screws difficult to remove as in much used oven 26 years, and thermocouple partially blocking socket ratchet wrench. Would have been easier with 1/4" short extension. Before detaching element, I used twist ties around the leads tied to a large plastic clip so as not to lose them into oven back. PartSelect part was made by GE, not secondary source. Perfect replacement for this old part - still available.
Read less
Was this helpful?
Thank you for voting!
Broiler element not working
-
Jone from Palmyra, VA
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
Some times it's not the element at all, as in this case. After rmoving the element I found the wires broke. Fortunatly I had some high temp wire left over from a earlier oven repair. I used butt splices and heat shrink tubing to repair the wires. Then I crimped on a couple of eyelets and fastened things dow.n I received a big kiss form th
... Read more
e wife for getting the broiler fixed so fast. Maybe a little extra work, but the rewards were worth it.
Read less
Was this helpful?
Thank you for voting!
exchanging broiler element
-
Beverlee from Mill Valley, CA
- Difficult
- 30 - 60 mins
Even though my sons offered to do the repair, I opted to hire an appliance technician to do it and it took him at least 45 mins. with his experience and tools. apparently the inside wall wires were shorter and more difficult to access and grip and I'm glad I did. It should last another 20 years and I'll be dead!
Was this helpful?
Thank you for voting!
broil element failure
-
Glenn from Plano, TX
- Really Easy
- 1- 2 hours
-
Pliers
Unscrew 4 easy nuts and 1 most difficult nut, gently pull both long and short wires, at this point assure the wife that you did turn off the power.You may wish to attach a cord to short wire as it wants to vanish into the rear bowels of the oven On instruction of the wife clean the oven. Reverse dismantling procedure. Switch oven on. Bask
... Read more
in wives praise.
Read less
Was this helpful?
Thank you for voting!
Old drip pans rusted out.
-
Joseph from San Antonio, TX
- A Bit Difficult
- Less than 15 mins
Range is 45 yrs old. New drip pans are different shape. This is only place which had them and VERY GOOD price. Delivery was quick, too!
Other Parts Used:
Was this helpful?
Thank you for voting!
element was not heating
-
JOHN from STREATOR, IL
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
I unscrewed the screw that held the element in place and then took the hex head nuts holding the 3 wires off the old element. When taking the wires off, I had the new element next the old and put each on the same connection one at a time to make sure I replaced the wires in the same location they were on the old element. After connectin
... Read more
g the 3 wires, I reattached the element to the range.
Read less
Was this helpful?
Thank you for voting!
Broiler Element Burned Out
-
Robert from Mission Viejo, CA
- Really Easy
- Less than 15 mins
-
Screw drivers, Wrench set
The repair was very eash. The replacement element fit perfectly and only involved removing two screws, pulling the old element out far enought from the bak of the oven to disconnect the wires held by two screws . Disconnecting the two wires and installing the new element. This is a 25 year old appliance and is back to working like new.
... Read more
One note, be sure to shut the power off to the range because one of the wires connected to the element remains HOT! even if the oven is not on.
Read less
Was this helpful?
Thank you for voting!
The burner only heated half of the coils
-
Patricia from Tamaqua, PA
- Easy
- Less than 15 mins
-
Pliers, Screw drivers, Wrench set
The repair went well and once again my stove that was installed back in 1968 is working perfectly. We will be buying another 6" burner and 2-8" so we have them when they begin to burn out. We looked everywhere for a replacement and was told they do not make them anymore, but we found it here. Thank you!
Was this helpful?
Thank you for voting!
old stained drip bowls
-
Peter J from Oceanside, CA
- Really Easy
- Less than 15 mins
I tried first to replace them, with a set I bought at a local hardware store. But they were too small. So I went on the internet, and found Part Select, and thanks to a very helpful guy, who made the extra effort to find the exact drip bowls, I now have a nice, shiny stove-top again. Installing them took two minutes... tilt the burners u
... Read more
p, and slide them in. No problem.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!