Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Bottom door trim was rusted
11 of 13 peoplefound this instruction helpful.
Timothy from Terre Haute, IN
Really Easy
Less than 15 mins
Screw drivers
Removed oven door and the 3 screws holding the bottom door trim. Attached new trim piece and reinstalled oven door. Entire job took less than 5 minutes.
Was this helpful?
Thank you for voting!
Oven light would not work--faulty socket
10 of 12 peoplefound this instruction helpful.
Delores from Warren, MN
Easy
15 - 30 mins
Screw drivers, Socket set
After removing the back of the stove, the old light socket was fairly easy to remove. The new socket slipped in place and the wires reattached and now the oven has a light again. A very simple process--especially for someone who's not an expert in repairing appliances.
Was this helpful?
Thank you for voting!
Broiler element failed
9 of 10 peoplefound this instruction helpful.
steven from SEDRO WOOLLEY, WA
Very Easy
15 - 30 mins
Screw drivers
Slide range out,unplug range,remove rear cover to unplug element wires, open door remove screws inside oven remove element
Was this helpful?
Thank you for voting!
Purchased home but stove had no broiler pan.
16 of 33 peoplefound this instruction helpful.
Raymond from BLOOMINGTON, MN
Very Easy
Less than 15 mins
Purchased 2 piece broiler pan from this site
Was this helpful?
Thank you for voting!
Burner control indicator light
10 of 15 peoplefound this instruction helpful.
George from Fredericksburg, PA
Easy
Less than 15 mins
Pliers, Screw drivers
Shut down breaker; remove stove back cover plate (8 screws); remove the control knob; remove knob screws (2); simply remove one wire at a time and replace the coresponding wire to the new control unit; remove the snap ring on the knob bar and snap off to fit the proper length; place the control unit in position and reinstall the 2 screws;
... Read more reinstall the back panel; position stove and turn throw the stove breaker on; test the burner control.
Read less
Was this helpful?
Thank you for voting!
Heating element burned up
8 of 10 peoplefound this instruction helpful.
Jerry D from Spring Valley, CA
Easy
15 - 30 mins
Screw drivers
It was simple. Unscrewed to screws at the back of the oven. Slipped off the wire connectors then attached the wire connectors to the new part, put the screws back in and we were back in business.
Was this helpful?
Thank you for voting!
DOOR HINGE BROKEN, NOT SUPPORTING DOOR
9 of 14 peoplefound this instruction helpful.
Charles from PAYETTE, ID
A Bit Difficult
30 - 60 mins
Screw drivers
Followed youtube instructions: lifted clips on door hinges, removed door. removed screws, removed rear cover, replaced right hinge. reassembled door. caution: door handle will fall off when top two screws are removed. Alignment of screws is some what difficult, requires awl. Replace door, return locking clips to forward position,
... Read morecheck door for operation.
Read less
Was this helpful?
Thank you for voting!
Oven wasn't preheating to temperature
8 of 11 peoplefound this instruction helpful.
Margaret from WALDORF, MD
Really Easy
30 - 60 mins
Screw drivers
Repair of oven sensor easy to install; however, product did not resolve the problem. Returned new sensor and awaiting refund (2 weeks passed so far).
Was this helpful?
Thank you for voting!
Both right and left side trims were broken.
6 of 6 peoplefound this instruction helpful.
A D from HOUSTON, TX
Really Easy
30 - 60 mins
Screw drivers
Ordered both parts using the excellent breakdown illustrations of the door. Received the parts along with video instructions on how to repair.
Element wasn't being controlled by the switch it would stay on high
6 of 7 peoplefound this instruction helpful.
George from FRANKLIN, KY
Very Easy
15 - 30 mins
Screw drivers
Ordered a new switch and replaced the old one with it.
Was this helpful?
Thank you for voting!
The burner would not shut off.
6 of 8 peoplefound this instruction helpful.
Richard from CONCORD, NH
Really Easy
15 - 30 mins
Pliers, Screw drivers
Pulled the dial off, unscrew two screws. Pull the switch out from the back. Disconnect the wires from the old switch and connect to the new switch one by one. Set the new switch in place. Sctew the two screws in to hold the switch in place. Push on the dial.
Was this helpful?
Thank you for voting!
light bulb in water ice freezer door went bad
8 of 14 peoplefound this instruction helpful.
Carl from RIVERSIDE, CA
Very Difficult
More than 2 hours
Screw drivers
I didn't. Don't know how to get to light bulb to change it for this specific model
Was this helpful?
Thank you for voting!
The heating coil was no longer working.
5 of 6 peoplefound this instruction helpful.
Amanda from Midwest City, OK
Really Easy
15 - 30 mins
Screw drivers
My husband pulled the oven out and unscrewed the screws(in the back) the heating element came right out. He did everything on his own. The only thing he needed a little help with was for me to keep the heating coil flush to the back wall of the oven, while he screwed the new one in. It was a very quick job. The longest part was pulling th
... Read moree oven out to get behind it and sliding it back in.
Read less
Was this helpful?
Thank you for voting!
Store-bought drip bowls wouldn't fit.
5 of 6 peoplefound this instruction helpful.
Sharon from Yacolt, WA
Really Easy
Less than 15 mins
My elements just plug in so all I had to do was pull them out and replace the drip bowls. They fit perfectly!
My Orders
