IVE30101 Inglis Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Sparks flying out of the oven, broiler element melting
2 of 2 people
found this instruction helpful.
-
corey from SHAKER HEIGHTS, OH
- Really Easy
- 15 - 30 mins
-
Screw drivers
First Things first, unplug unit, remove rear cover with Phillips head screwdriver, disconnect, wires from broiler element which is the top, one, open oven, unscrew top screws first, then two at the back, wiggle out element, then reverse Steps , test repair before putting cover back on. Then ta-da, you saved yourself a $300. Service c
... Read more
all to the appliance repair guy.
Read less
Was this helpful?
Thank you for voting!
Broiler element burned out
3 of 5 people
found this instruction helpful.
-
chris from HILTON HEAD, SC
- Really Easy
- 15 - 30 mins
-
Screw drivers
After doing a YouTube search. I successfully completed the repair by easily diagnosing the issue with the element.
I watched a video about 5 most common problems with whirlpool broiler elements.
The first being to inspect the element for damage. I found a small section that appeared to be rough and had a raised bump.
I ... Read more decided to order a new element because the oven is older and it wouldn’t hurt to install a new one even if this wasn’t the issue.
Once the part arrived, which it did quickly, I followed the video instructions. It was easy and straight forward. I completed the task in under thirty minutes. It was very simple and I now have a functional broiler element.
I watched a video about 5 most common problems with whirlpool broiler elements.
The first being to inspect the element for damage. I found a small section that appeared to be rough and had a raised bump.
I ... Read more decided to order a new element because the oven is older and it wouldn’t hurt to install a new one even if this wasn’t the issue.
Once the part arrived, which it did quickly, I followed the video instructions. It was easy and straight forward. I completed the task in under thirty minutes. It was very simple and I now have a functional broiler element.
Read less
Was this helpful?
Thank you for voting!
Drawer guides missingJust
3 of 5 people
found this instruction helpful.
-
Mark from Killbuck, OH
- Really Easy
- 15 - 30 mins
-
Screw drivers
Just follow included instructions.
Was this helpful?
Thank you for voting!
outer glass on door broke
3 of 5 people
found this instruction helpful.
-
Marc from FOXBORO, MA
- Very Easy
- 15 - 30 mins
-
Screw drivers
used a screwdriver. took very little time and effort
Was this helpful?
Thank you for voting!
Heating element, broken
2 of 2 people
found this instruction helpful.
-
Frank from COLUMBIA, TN
- Very Easy
- Less than 15 mins
-
Pliers, Screw drivers
Unplugged appliance, removed the 2 screws that mount element. Unhooked the electric wires,with pliers.
Connected, the wires to new element replaced the 2 screws. And was done in about 9 minutes.
Connected, the wires to new element replaced the 2 screws. And was done in about 9 minutes.
Was this helpful?
Thank you for voting!
temp level uneven
2 of 3 people
found this instruction helpful.
-
Paul from HARMONY, MN
- Very Easy
- 15 - 30 mins
after watching the video, installed the temp sensor. Super easy
Was this helpful?
Thank you for voting!
the oven temperature was not working right. I installed a new oven sensor. Works get now
3 of 6 people
found this instruction helpful.
-
Rosalind from APOLLO, PA
- Very Easy
- 15 - 30 mins
-
Screw drivers
Watch the video...
Was this helpful?
Thank you for voting!
Burner did not always reduce heat when temp. Was lowered.
2 of 3 people
found this instruction helpful.
-
Annie S from RIDGEVILLE, SC
- Really Easy
- 15 - 30 mins
-
Screw drivers
My husband unscrewed the bad switch and replaced with the new one.
Was this helpful?
Thank you for voting!
Used part
2 of 3 people
found this instruction helpful.
-
Sabrina from FREMONT, CA
- Very Easy
- Less than 15 mins
Lift burners out of plug discard old drip pans replace new drip pans into plugs and done .
Other Parts Used:
Was this helpful?
Thank you for voting!
screw came off
1 person
found this instruction helpful.
-
Sandeep from EDINA, MN
- Very Easy
- Less than 15 mins
-
Screw drivers
very expensive to buy the part but just tighten the screw intot eh predefined place.
Was this helpful?
Thank you for voting!
Oven Elementwas burnt into
1 person
found this instruction helpful.
-
Fred from APACHE JCT, AZ
- Very Easy
- Less than 15 mins
-
Screw drivers
Watched the video and did as shown
Was this helpful?
Thank you for voting!
Couldn't find correct drip bowls that fit.
2 of 4 people
found this instruction helpful.
-
Lowell from Hardin, KY
- Really Easy
- Less than 15 mins
Removed old drip bowls, removed burners installed new drip bowls,installed burners. They fit perfect and I received them two days after ordering.
Other Parts Used:
Was this helpful?
Thank you for voting!
The old drip bowls were rusting, no chrome left
3 of 7 people
found this instruction helpful.
-
kathryn from piqua, OH
- Really Easy
- Less than 15 mins
Took the old ones out and put in the new ones! What I am so pleased about it that I just went online and at Parts Select website it was easy to find what I needed, a fair price and the 4 bowls arrived within 2 days!
Other Parts Used:
Was this helpful?
Thank you for voting!
Oven Demon Possession
1 person
found this instruction helpful.
-
Kevin from Greensboro, NC
- Really Easy
- Less than 15 mins
Our repair was extrodinarily easy. As my husband was taking out the old element and the oven was off, the element heated up and actually burned him. He readjusted it and it refused to heat again. We figured at that point that there must be a short, so we never even opened the box with the new element. A short time later we decided to use
... Read more
the top of the stove for soup and a small fire started in the oven. We turned off the braker at that point and ordered a new oven.
Read less
Was this helpful?
Thank you for voting!
baking element non operational
1 person
found this instruction helpful.
-
GARY from JACKSON, WY
- Really Easy
- Less than 15 mins
-
Screw drivers
removed two screws to faceplate at rear of oven. Disconntected contact wires, installed bake element reconnected contact wires, attached faceplate turned on oven holy hell it works just saved some money on service call thanks!!!
Was this helpful?
Thank you for voting!