IRH32002 Inglis Microwave - Instructions

I called the repair/parts number to make sure I had correct parts and the young lady instructed me as to the size of the serving tray; within 48 hours we had the VERY carefully wrapped carton opened and back in the microwave, working perfectly. Thank you. We'll recommend you to our friends!

Removed the two philips screws installed new grill and replaced the screws.

Just be sure to push both sides of the grille into place and screws were easy to tighten. The filter is not difficult at all. Made me proud to repair it myself (73 yoa)

Twas really easy considering that all I had to do was place the plate back in the microwave. Easy Peasey

Tray arrived in a short period of time and was a perfect match.

replaced burnt parts

Not so sure this would qualify as "instructions", but I only needed a screwdriver because the "D" rings of the old vent filters broke off and I had to pry to old ones out. Keep in mind, I am mechanically disadvantaged and can barely change an A/C filter ... that being said, all I did for this order was input my Model number and PartSelect found the correct replacement part. I receive the parts super quick (faster than the other 2 purchases I did that day). The only bummer was the packaging ... super huge box for small tiny parts. Otherwise, I now know where to go for replacement parts. This project should be a "no-brainer" for most DYI's, so getting the right parts with just a model number was lifesaving for me :0)

just replace need cooking tray

Removed all the screws from the underside panel - approximately 9 or 10 of them. The panel easily dropped down to allow easy access to the light bulb socket assembly. The wires to the socket easily unplugged and old socket easily removed. New socket slipped right in and wires easily plugged in. Actually took longer to put the screws back in than anything else. I am thrilled with this repair. Note: so easy even a 61 year old single woman in her PJ's can do it.

I didn't do the repair -- my husband did, said it was easy, had no problems what so ever! The new bulbs give a lot more light to the cooking area.

I had been dealing with a broken vent cover and burned out light for several months. I should have fixed it much sooner if I knew how easy it was. PartSelect.com had pictures of everything I needed and after reading the repair stories I was able to disassemble the pieces necessary and clean them before reinstalling. Very fast shipping also. The vent grille attaches easily with a couple screws. It's weakest point is the plastic tabs which will break and then gravity puts the grill in the doors ways. The light bulbs can be accessed with a hinged glass door (one screw) but be careful they are very fragil and can break off. If they do unplug your unit, get a pair of needle nose pliers and slowly unscrew the rest of the bulb. If you wanting room or you want to clean the grease off, I recommend removing the whole bottom cover from the microwave (7 scews and 2 wire harness clips).

It was supposed to be a very easy replacement, but when inserted the legs in the bottom openings, the legs at the top didn't enter the opening.If insert first the top legs then the bottom legs could not go in. Tried to put a little force when turning grill to enter the top legs with the screws support. Finally very carefully put first the top legs, entering horizontally, and then giving a little push (forcing) the bottom legs in. This was not supposed to be this way, because I could had brake the bottom legs clip.

1. Unplug the power cord from the wall socket. 2. Remove the 10 screws holding the bottom cabinet cover in place. The bottom cabinet cover will swing down allowing acces to the inside ofe the microwave. 3. Remove the connector from the turntable motor. 4. Use a T15 Torx driver to remove the 2 Torx screws holding the motor in place. 5. Remove the motor. 6. Reverse the process using the new motor.

Removed 2 screws that were holding broken plastic tabs. Lined up lower plastic tabs on new grille into slots, gently. Tipped forward to engage upper tabs into slots. You need to "gently" press the top into place to avoid breaking off the tabs! Replace 2 screws, and hand tighten with Phillips screwdriver. Easier to see what you're doing with the microwave door "open". I felt "accomplished" for a 70-year old Grandma.:)

Wedged grill into open space and screwed in with existing screws