IP82000 Inglis Dryer - Parts

If you notice that your dryer is noisy or will not tumble, you may need to replace the tri ring. This part is triangular, and is less than an inch in size. Tri rings can be found both on the idler pulley shaft, or on the rear drum roller shaft. In either case, you will need to remove the front panel of the dryer and the drum to access the...Read more part for repair. Once you have accessed the damaged tri ring, you will simply need to slip it off and replace it with the new one. This part is sold individually. Be sure to disconnect the power source from the dryer before you begin this repair.

If your washer shakes or vibrates loudly when it reaches its max speed, check that the leveling legs are even. To ensure that the washer is firmly on the ground using all four legs, adjust the legs so that the machine is level, and tighten the locking nuts on the legs that are threaded. Keep the washer as close to the floor as possible. Y...Read moreour model might have rear legs that level themselves, or it might have threaded legs all around. Make sure the rubber feet have not worn out. Replace any missing or damaged legs and feet. This replacement part is sold individually.

This OEM drive motor is designed to operate the drum in electric and gas dryers by turning the drive belt, enabling proper rotation during drying cycles. Compatible with most Whirlpool-incorporated dryer brands manufactured before 1996, it includes a pre-attached pulley, which is not available separately. If the motor has shorted out or f...Read moreailed, the drum will no longer spin, and replacement is necessary to restore full functionality. Installation requires disconnecting the dryer from its power source before removing the old motor and installing the new one. This component is sold individually and meets original equipment standards for performance and reliability.

This kit is used for electric clothes dryers, and it comes with a yellow wire nut.

This is a genuine OEM replacement rear drum seal for your dryer. This seal is made of felt and comes with the adhesive required for installation. The purpose of the seal is to prevent hot air from escaping the drum while the dryer is operating. If you notice that it is taking too long for your laundry to dry, that marks are left on your l...Read moreaundry, or the machine is noisy or will not tumble, then you may need to replace the seal.

This 10-watt clear incandescent light bulb is designed to provide reliable interior illumination for household appliances such as dryers and refrigerators. Measuring approximately 2 inches in length, it fits securely into standard appliance sockets and activates when the appliance door is opened, offering clear visibility inside the drum ...Read moreor compartment. The bulb is suitable for use in a wide range of models across multiple appliance brands and is engineered to deliver consistent performance and durability. Installation is straightforward—simply screw the bulb into the designated socket within the appliance. Ensure the appliance is powered off before installation to maintain safety.

This screw is sold individually.

The blower wheel is a squirrel cage type wheel whose purpose is to move the air through the room or appliance. The blower wheel spins on the motor shaft to blow air through the dryer drum and out through the exhaust.

This is foam seal for your dryer. It forms a seal to prevent air from escaping the rear of the dryer drum and the lint duct. This model comes with adhesive backing and is located in between the lint chute and the bulkhead of your appliance. This foam seal is just over 28 inches long and under 1 inch wide. You may need to replace this part...Read more if your clothing is taking too long to dry, or if your dryer is not generating enough heat or no heat at all.

This dryer drum bearing ring kit is a vital component that supports the front of the drum, reducing friction and ensuring smooth rotation during operation. Engineered for durability and quiet performance, it helps minimize noise and vibration while preventing wear between the drum and the dryer casing. Replacing a worn or damaged bearing ...Read morering can restore proper drum movement and prevent further damage to internal components. Common symptoms of a failing bearing include loud noises, excessive vibration, and difficulty with drum rotation. Installing this part helps maintain efficient and safe dryer operation.

This dryer door seal is designed to create a secure, insulated barrier around the door opening, preventing heat from escaping and external air from entering during operation. Made from high-temperature-resistant, durable material, it enhances energy efficiency by maintaining consistent internal temperatures, resulting in faster drying cyc...Read moreles and reduced energy consumption. A properly functioning seal also helps prevent safety hazards associated with air leaks and ensures optimal performance. Replacing a worn or damaged gasket restores the dryer’s ability to retain heat and operate effectively.

The WP8066184 is a dryer motor pulley that is used in some dryer models. It supports the motor belt where it connects with the motor. Symptoms of failure include squealing or grinding noise during drum rotation. Please use the model number of the appliance to check for compatibility before purchasing.