All Installation Instructions for Inglis Range IME31301

the oven temperature was not working right. I installed a new oven sensor. Works get now

3 of 6 people found this instruction helpful.

Rosalind from APOLLO, PA
Very Easy
15 - 30 mins
Screw drivers

Watch the video...

Was this helpful?

could not control the temp of the element

2 of 3 people found this instruction helpful.

Steve from GREENBRIER, TN
Very Easy
Less than 15 mins
Nutdriver, Screw drivers

take off back panel, simply unplug the old switch and plug in the new one. Simple

Was this helpful?

burner plug broken

2 of 3 people found this instruction helpful.

Norman from Newport, NC
Really Easy
15 - 30 mins
Pliers, Screw drivers

Cut wires removed old plug,new plug in wire nuts on.Put heat on shrink tube done.
Less than 30 min.

Was this helpful?

surface element out

1 person found this instruction helpful.

Edward from TAYLORS, SC
Really Easy
15 - 30 mins
Screw drivers

Unplug from outlet and top remove back section of range and unplug wiring from switch, remove knob and unscrew two screws and remove old switch. Install new switch reinstall screws and plug switch plugs into new switch (will only go on the correct way). reattach back and plug into outlet. All done and surface element works perfectly.

Was this helpful?

element not working properly

1 person found this instruction helpful.

PHILIP from NORTH PORT, FL
Really Easy
15 - 30 mins
Screw drivers

Remove 2 screws inside oven holding element . Remove screws holding back panel. Plug wires (2) into new element.Install back panel . Done.

Was this helpful?

Burner wouldn't regulate temperature

1 person found this instruction helpful.

Michael from THE VILLAGES, FL
Really Easy
15 - 30 mins
Screw drivers

Turned off power to range. Took back panel off to reveal all controls. Pulled off knob of bad control. Removed 2 screws from the front of the control. Pulled off wiring from back of old control. Took new control reversed procedure. Reinstalled back panel turned power on and tested new control. Total time about 20 minutes

Was this helpful?

Oven would not heat up.

1 person found this instruction helpful.

Johnie from PARKERSBURG, WV
Really Easy
15 - 30 mins
Screw drivers

Unplugged the range. Opened the oven door and took out the shelves. Took the right screw out, but had trouble getting the left one out do to the age of the range. Unhooked the two wires and took the element out. Put the new one in and hooked up the two wires. Attached the two screws and checked to see that the element laid flat and t ... Read more

Read less

Was this helpful?

8" FRONT BURNER STAYED ON HIGH HEAT/WOULD NOT REDUCE TEMPERTURE

1 person found this instruction helpful.

RICHARD from DELTONA, FL
Really Easy
15 - 30 mins
Screw drivers

REMOVE BACK OF RANGE, REMOVE BURNER KNOB. REMOVE SWITCH CONTROL REMOVE WIRES. REPLACE WIRES ON NEW SWITCH. INSERTED ALL WIRES REPLACE NEW SWITCH RE REPLACE ALL SCREWS. CHECK SWITCH. TURN BRAKER BACK ON. CHECK SWITCH FUNCTION. ALL IS FINE. PUT BACK ON RANGE SCREW IT IN PLACE. MOVE RANGE BACK IN IT POSITION.

Was this helpful?

broken rear drawer glides

1 person found this instruction helpful.

Jeff from Manhattan, KS
Really Easy
15 - 30 mins
Screw drivers

just replaced the broken glides with the new ones.

Was this helpful?

Element had burned out, and the drawer glides were broken .

1 person found this instruction helpful.

Allen from ASHLAND, PA
Very Easy
15 - 30 mins
Screw drivers

Replaced both .

Other Parts Used:

Oven Bake Element

Range Rear Drawer Glide

Was this helpful?

Broke drawer bracket

1 person found this instruction helpful.

Valerie from ROCHESTER, MN
Very Easy
Less than 15 mins
Screw drivers

Was super easy even I could do it. Wish I would have done it 2 years ago when my husband broke it. Just used a Phillips screwdriver. Very easy!

Was this helpful?

Removing an heating element that burnt into .

1 person found this instruction helpful.

Jenny from GREENFIELD, IN
Very Easy
Less than 15 mins
Pliers, Screw drivers

Unplugged oven , removed screws ,pulled wires out, removed old element , just hooked wires up , screws .make sure it sits level plugged in. Works great

Was this helpful?

2 Service Elements Didn't Work (Didn't heat up)

1 person found this instruction helpful.

Roseann from MEADVILLE, PA
Very Easy
Less than 15 mins

Unplugged old elements and plugged in new ones

Other Parts Used:

Range Surface Element

Standard Y-Frame Range Surface Burner

Was this helpful?

Broken drawer glide

1 person found this instruction helpful.

karen from Thornton, CO
Really Easy
Less than 15 mins
Screw drivers

Used a phillips head screwdriver to remove the single screw holding the part in place and put the new one on. Finding the part on this site was a breeze and it arrived quickly. A first rate experience all around.

Was this helpful?

Worn/Bulb Socket

2 of 4 people found this instruction helpful.

JOSEPH from COON RAPIDS, MN
Really Easy
Less than 15 mins
Screw drivers

It was alittle difficult at 1st to remove the clips that held in the socket. But once out everything went smoothly.

Was this helpful?

IME31301 Inglis Range - Instructions