IM34 Frigidaire Ice Maker - Parts

This 8-cube ice maker is used to create ice for your refrigerator. The ice maker receives water from the water inlet valve and will freeze until ice cubes are formed. Once the water has been frozen the cubes will be ejected from the mold in to the ice bucket. The ice maker will continue the process until the ice bucket has reached the l...Read moreimit. If your ice maker is not making ice you may need to replace this part. Please remember to disconnect the power and water supply before starting your repair. This ice maker is a genuine OEM part.

This replacement icemaker may also be known as the ice maker assembly and is compatible with your refrigerator/freezer. This assembly replaces the heat-release ice maker unit only. The kit comes with four round female connectors at the end of the wire harness. It also comes with the adaptor that converts the harness to three round female,...Read more and one round male connectors. The tools you will need in order to make this installation include a 1/4-inch nut driver, and a Phillips screwdriver. Before starting this repair make sure to unplug your refrigerator and shut off the water supply.

The ejector drive gear is a part for your refrigerator. This icemaker drive gear is for the ejector blades. The part rotates the cube ejector arm, which cycles the icemaker and pushes the cubes out and into the ice bucket, ready for the ice to be used. The outside diameter of this piece is almost two inches by two inches. The reason for n...Read moreeeding to replace your gear is if the current one is broken/missing a tooth, or if your icemaker is not dispensing ice and is noisy.

The ice stripper goes on the front of the ice maker and directs the ice cubes from the maker to the bin. Due to the frigid temperatures, the plastic breaks down and cracks from time to time. This may cause the ice cubes to get stuck in the ice maker and not dispense properly. You will need to open the freezer door, pull out the ice contai...Read morener by lifting and pulling out. Unplug the ice maker by releasing the locking tabs. Use your 1/4-inch nut driver to remove the screws holding the ice maker in place. Take the ice maker out of the freezer for easy access. The ice stripper can be removed by simply unlatching from the pin holding it in place. The new ice stripper should just click into place so the tab goes into the control head with ease.

The micro switch in your refrigerator aids in the dispensing of ice and water. This micro switch controls the on/off function of the ice/water dispenser of your refrigerator. If you notice that your refrigerator is not dispensing ice or water properly, you may need to replace your micro switch. This part is made of black plastic, with thr...Read moreee metal prongs. The plastic portion of this part is approximately one inch in length. This is an OEM part sourced directly from the manufacturer. Be sure to unplug your refrigerator from the power source before you begin this repair.

This part is a one-time limit fuse used as a safety device. Once tripped, this part must be replaced.

This ice container is white in color and made of plastic. This part lays flat inside the freezer compartment. The container is approximately 13 inches front to back, 10 inches side-to-side, and 5 inches deep, weighing 2 lbs. The ice container holds the ice in the freezer section for dispensing. Due to the frigid temperatures of your freez...Read moreer, plastic can break and crack over time and will need to be replaced. This is an OEM part that is sourced right from the manufacturer, ensuring the best possible quality.

Sold individually.

This genuine replacement shutoff arm spring is for refrigerator ice makers. It applies tension to the ice maker shutoff arm to hold it in place so that the ice maker will stop making ice when the ice bucket is full. If your ice maker continues to make ice when your bucket is full, you may need to replace this shutoff arm spring. This part...Read more is less than 2 inches long, and is made entirely of metal. Be sure to disconnect the power or the water supply to your refrigerator before completing this repair.

1/4"diameter - 93" long - plastic - cut-to fit

The ice maker shut-off lever is an OEM replacement part specifically designed to control the production of ice in your refrigerator. It is typically located inside the freezer compartment, near the ice maker. The shut-off lever is responsible for controlling the ice maker functions. When the lever is in the raised position, the ice maker ...Read moreturns off and stops the ice production. Conversely, when the lever is pushed down, the ice maker produces ice cubes. This mechanism allows you to control the ice-making process to suit your needs. A faulty shut-off lever will result in nonstop ice production or no ice production at all. Carefully detach the old lever from its housing and position the new shut-off lever in its place. Finally, reactivate the ice maker and verify that it functions correctly by observing the ice production cycle.