IJP85801 Inglis Range - Instructions

turned off power
removed ceran top from cabinet
removed element
installed new element
replaced top
powered up and was done

I numbered every part. ex: 1 L., for first part removed left side. I used a magic marker to circle the holes and wrote the number of screws used on the part, set the srews in a separete place, so that I new where these screws went to. The cleanup was pretty time consuming, but I was able to keep my stove, when every repairman I called to ... Read more fix my stove told me I was better off buying a new stove. ($600.00 stove 2 years old)Please Note: The insulation blanket needed for the entire stove is two pieces, the sides and top are one part # and the bottom and back, are another part #. I did not know this. I just purchased the top and sides. I got lucky, the back and bottom were still in good shape. So I guess I should have read the description of the part more carefully to see what it covers, before I ordered it. It took two people two hours to do the work, it was really nice to have an extra set of eyes, to remember what direction pieces of metal from the stove went. I would do it all over in a heart beat instead of buying a new stove.

Bought new element and installed. Very simple. Used phillips
screw driver.

Unplug range and remove back panel (4 screws) unplug top burner plugs (2). Open oven door and remove 2 screws from under front of top. Pull top out and up to unhook from back. Remove top and lay cardboard on top of range. Flip over the ranges glass top unit and lay on cardboard. Remove screws from steel bottom and remove from top. Flip ov ... Read more er steel bottom with burners attached. Remove attaching clips for burner and unscrew them from the burner then reinstall in new burner in the same place as old burner. Lay new burner on top of old burner and remove one wire at a time, transfering it to the matching plug on the new burner. When wiring is done remove old burner and attach 2 clips to steel backing plate. Vacuum off the glass top and reinstall the steel bottom to the glass top. Flip over the top, remove cardboard and slide top into back of range top and lower into place. Attach 2 screws under front. Reattach the tops plugs at the rear and reattach the back panel. Plug in range and slide back into place. Test units and all other burners. Done...

Socket Lite come with clips attached to the outside
of the housing. After you unhook the 3 lead wires
that are attached to the unit. All you have to do is push in on the clips and release the unit. Then you
snap in the new unit. Attach the 3 wire leads, put a
oven bulb in the socket end, and the install the light cove ... Read more r

The element went out and I ordered the element on about 3:00 P.M. on Friday and before 9:00 A.M. on Saturday the unit was on my front porch. Couldn't believe how quick it was! Thanks for the good service. Ted Samuelson

Removed oven from wall unit and took the back off. Removed the old socket assembly by depressing the ears and forcing unit into the oven. The electrical wires were easily removed since they are spade connections and slip off. They also are different sizes so that there is no chance of erroneously putting them back in an incorrect order. ... Read more The new unit simply slips in from the front and snaps into place. The most difficult part of the entire process is removing the old unit. A little "friendly persuasion" is required to get the old unit out.

Take the door off the oven by sliding out the old hinges that hold the door on to the oven. Put the door up on a protected table so that the hinges can hang down and free of the table. This step will make the job go much more simple. Proceed by removing all visable screws. Make a mental note on how the old hinges are held in and how t ... Read more he door comes apart. Take your time this is not a hard task! I am a homemaker, was taking care of my grandson that day and still accomplished the task in under an hour. The repair people wanted $145.00 labor only to install this part!

I turned off the breaker (I'm a little nervous even unplugging a 220 plug). I first removed the cover from the back of the stove to get to the wiring/socket. Removed the two wires from the leads - they just pull off by hand but use a needlenose pilers if it is stuck. One is larger so no need to try to remember which one goes where. I re ... Read more moved the glass cover and bulb from inside the oven. I read another post on this site that said there were clips that you had to press to get the old socket out which helped. That part was a little tricky as the insulation around the socket makes it hard to see and the opening is really tight. I finally found the clips and pressed one then got that side out enough to hold the clip back then pressed the other clip and I was able to push it right out. I did not have the strength to press both clips with enough pressure but if you do, that would probably be easier. From inside the oven, I pushed the new socket through the hole - there was a little notch in the opening that had to match up with the socket. I had to push pretty firmly until I felt both clips snap in place. Replaced the wires, turned on the power, screwed in the bulb and cover and I had light!

real easy one to take care of, when the drawer broke I thought it was more than what it really was, after looking at it and seeing the wheel was gone I ordered the part and it came very quick, drawer is now fixed.

All I had to do was unscrew the pyrex lens over the oven light and then remove the old gasket and replace it with the new one. Worked like a champ!

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

Easy repair with Phillips screw driver and needle nose pliers. 1. Turn off Breakers or unplug range, Open oven door and remove the two screws holding the glass top to the oven frame. 2. Slide glass top forward and remove the two electrical connectors at the rear of the glass top, one on each side. 3. Remove the Phillips screw holding t ... Read more he ground wire from the rear top flange of the glass top. 4. Glass top can now be removed and placed glass side down on a padded flat table top. 5. Take a few pictures of the wiring and brackets for reassembly reference. 6. Remove the 4 wires from the defective heating element with needle nose pliers (note locations for reassembly to the new element) 7. Remove the Phillips screw on the rear side of the bracket holding the defective element. Carefully lift off the bracket. 8. Heating element can now be removed. 9. Remove the locating flanges from the defective element and install on the new element in the same locations. Clean glass if necessary and place new element on glass. 10. Carefully locate the flange tangs into the same holes on the bracket, reference photos or other side for locations. Ensure small element bracket was replaced in mounting slot of large bracket and reattach bracket screw. 11. Replace wires to same locations, remove and lightly pinch connectors if they appear loose, then reassemble. 12. Replace glass top on range, reconnect the two electrical connectors and ground wire, slide forward and replace the two mounting screws. 13. Restore power and check new element for function. Extension wires which came with the new element were not needed in this application. Total repair time about 20 min.

After removing the back of the stove, the old light socket was fairly easy to remove. The new socket slipped in place and the wires reattached and now the oven has a light again. A very simple process--especially for someone who's not an expert in repairing appliances.

I read it may be the temp sensor. Ordered a new one. Took a minute to undo three screws holding the back on, and one screw for the sensor. But still didn't work. Then realized maybe the oven was changed to Celsius. In manual - open door, hold broil for seconds and changed back to Fahrenheit.