IF36INDFSF Dacor Refrigerator - Instructions

I just opened up the fridge back panel accessed the old relay/capacitor, pulled it out, replaced with the new one, snapped it back into place, tested it (compressor came on), replaced the back panel and went on my way. Really, really easy repair.

I used a flat screwdriver and released the lock tab on the bottom of the light switch, and pried the switch out, being careful to not damage the plastic around the mounting place of the switch, unplugged wiring from old switch, plugged in the new one and pushed the new switch into place. Job finished light switch now working.

First I removed the plastic light shield. That snaps into place. Next I removed the plastic facade which snaps in from behind. It has plastic mounting points, I had to use a long straight screwdriver to do this. Then I unplugged the old board and replced with new.

An easy job for smaller hands. Removed the two bolts holding the light cover. Removed two electrical connections from the old switch by pinching the retaining clip,removed the switch, snapped in the new one and re-attached the connectors. Your online illustrations helped me to know that the plastic housing for the light switch would only ... Read more swing down so far and was not intended to be removed. Saved me from breaking that plastic cover's tabs. This home repair saved me more than 5 times the cost of hiring a professional to do it. Very happy homeowner.

The lid that covers the front of the lower meat / produce drawer hinges upward on two small ( easily broken) plasic pins, one on each side of the drawer. One pin is moulded into each "END CAP" that also supports the drawer glides and glass shelf above. The entire end cap must be replaced to repair the hinge. The left side is easy (it's ... Read more the only one I had to replace); the right side might be more difficult because the right end cap includes a temperature control.
1) Remove the two produce drawers above the lower drawer.
2) Lift off the front glass shelf support, the glass shelf, and the rear glass shelf support from below the two produce drawers.
3) Slide the lower drawer half way out. Remove the drawer lid by disengaging it from the remaining undamaged hinge pin on the OK end cap. Careful not to break the good one.
4) Slide the lower drawer all the way out, then lift up and towards you to remove it from its glides.
5) Using a 1/4" nutdriver or socket, remove the three recessed screws. Leave the drawer glide alone for now.
6) Pull the front of the end cap up and towards you about 3/4" to disengage it from a small retainig button at the top front. Pull the end cap toward you to disengage the two rear retaining fingers.
7) Using a small Phillips screwdriver, remove the drawer glide from the broken end cap and attach it to the replacement end cap. Note which end is the front before removing it.
8) Reassemble in reverse order. Again, be careful with the hinge pins.

Perhaps a helpful hint:

When aI received the hose adapter/connector, I inserted the 2 hose ends only to have water drip from the connection.
I used a utility knife to remove an inch from each side, then reinserted the hoses. That made the differnce. Dry as a bone.

LG

Ordered a new filter cover, received in 2 days and installed it in about 5 minutes. Worked perfectly.

The tiny piece of plastic that holds the wire that shuts off the icemaker, broke early on with our fridge (after just a few months.) We superglued it, but last week it bit the dust for good.

Once I got this part, I removed the freezer door and trays, and pulled the icemaker out by removing 3 flathead screws and unplugging the c ... Read more ables. Laying in the freezer on the floor was a bit unconfortable, but not too bad.

Then I inspected the icemaker. There was no obvious way to remove the part without disassembling the front of the unit (where the motor is) to release the spindle and free the part, so I did that - 3 or 4 nuts was all that held it together. Once that was out, I removed the spindle, swapped out the part, and put it all back together and back in the freezer. Plugged it in and waited.

It took a while to start making ice. Like 5 hours. Now it's going pretty slow (much slower than before.) Haven't had time to look into it, but my suspicion is the rubber hose that feeds water into the icemaker is blocked with ice or kinked. In any case, we have ice now (but not a lot), and the unit shuts itself off properly. However, we went from having too much ice (thing never shut off) to too little (thing makes ice too slow), so I need to shoot for somewhere in the middle ;)

Remove the light cover. Use a flat head screw driver to push in the tabs on the back of the program mount and pull down to expose the computer board. The Thermistor is clipped on under the vent holes on the right side. Cut both wires to remove the old thermistor strip a 1/4 inch off the remaning wires and the new thermistor wires twist bo ... Read more th ends together crimp on the wire caps snap in the new thermistor reinstall the program board until the retainer clips snap into place, slide the light cover back on.

Removed screws from cover tested for power to motor found power was on to motor but motor did not work. I went to your web site was able to locate part in about 5 minutes . Even with over night shipping the part came to about $50,00, far cheaper tha a service call would have been.

Thanks John Paulsell

Once I saw the replacement part I understood how to pry out the switch with a small screwdriver. Then just unplug the old one, plug in the new one and pop it into place.

The PartSelect site made it easy to correctly identify the correct part, it was inexpensive, and the shipping was fast.

I'm very pleased!

Turn water and refrigerator off, use hair to thaw the ice maker filler tube, then remove the filler tube inside the freezer. Next remove the water supply line cover plate in back of the refrigerator. Now remove the speed clip at the white pvc elbow and pull out the supply line. Next, grasp the pvc elbow with pliers and pull hard to rem ... Read more ove. The new filler tube is a 1 piece design (filler tube and elbow combined) and needs to be cut to the proper length. Mark it inside the freezer, remove it and cut to length. Now coat the outside flange with caulk or PU glue and snap into the opening. Put the speed clip on the elbow first and center it. Ensure that the spreader insert is in place in the plastic tube, then slide the supply line into the elbow untill completely engaged. Replace cover.

Pushed the hinge pins aside and removed the old lid.. Reversed the process to install the new lid

Took two times getting the correct part, however after getting the correct part it took about 10-minutes to replace. Had to take the fan out. When you put the new drip pan in make sure it is positioned so that the guides on the pan aligns with slots in the bottom refrig brace, otherwise back pannel will not align correctly. The fan is ve ... Read more ry easy getting aligned in the new tray. May take a little effort. I do not know why the pan on a refrighterator that is less than 5-years old could start breaking into many pieces.

Pantry Cover:

I just slided out the tray, and unscrewed the left pantry panel that was broken, and replaced it with the new one, then put in the new cover after sliding the trays back in.

Ice Maker:

I unplugged the power connector in the back, unscrewed the ice maker with a flat screw driver (3 screws), s ... Read more lide it out, and then unplugged the wiring from the old ice maker and put it into the new one, mounted the new ice maker back in, make sure the lever is working, and then closed the freezer to let it cool down so that water can start flowing to it when it becomes cold enough (took about a good hour or so before water started filling the ice maker). Once the freezer was cold enough, water started filling the ice maker, and it begin making ice again.