IEL730CS0 Whirlpool Range - Instructions

Turned off power
Removed door
Removed a few screws
Take out elements and replace with new ones
Very easy process

Followed a video I found online showing how to replace the bottom bake element. It was very easy to do. I simply unplugged the over, removed the back wire cover and detached the damaged element connectors.

I then removed the bottom oven cover which conceals the element. Unscrewed and removed the damaged element and replaced it ... Read more with the new one. Connected the wires to the new element and then Installed the bottom cover along with the back wire cover and plugged the oven back in. It was really this easy.

I removed the bottom drawer,unplugged the Range and pulled it out to expose the rear cover panel. Using a nut driver (a screw driver can be used), I removed the rear panel to expose the Thermal fuse located almost dead center in the back of the Range. Unplug the two wires and loosen the screw holding it in position. Replace the thermal ... Read more fuse, plug the two wires into the new part and replace the rear cover panel. Return the Range to its original position and plug it in. The job is done in less than 30 minutes.

I shut off the breaker to the stove. I removed 2 screws from the underside of the cooktop at the front of the unit. I raised the cooktop and had my helper hold the top at an angle to access the burner. I removed 2 screws attached to the burner and then loosened the 2 clips and moved them to release the burner. I transferred the electrical ... Read more connections from the old to the new. Reinstalled the burner and cooktop. Turned the breaker on, tested the new burner and I was fone

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

I first shut off the breaker, then, after pulling the stove away from the wall, I unplugged it. I removed the two screws in the back of the stove which came off easily. I removed the two screws inside the oven and removed the bottom plate. I noticed the heating element I was changing had braces along the bottom. I had to remove the two s ... Read more crews and removed the burnt out element. The new element did not have the braces the original element had, but it fit in perfectly. Then I replaced all the screws, plugged it in and turned on the breaker and it worked. The only thing that we noticed is there’s a clicking sound every time the temperature increases. Not sure what that is.

Replaced the oven light with a new one but it burnt out as soon as I turned it on. Therefore I decided a new socket may help.

My whirlpool apparently has the old style socket which is pictured in partselect part #PS12584564. The old style socket has to two metal arms that retain it against the metal reflector.

The ... Read more part that will come (#PS12584564) however is the new style that whirlpool has changed to, apparently. It is not as pictured. The socket and the reflector have different retention devices.

I used screw drivers to bend the two metal arms away to release the socket. Then I had to use allen wrenches to bend the reflector's retention tabs away.

Once I had the old socket, reflector, and lens replaced I just followed the video on partselect for part #PS12584564

Had an electrician to do the job for me.

Turn off 220 voltage, unplug and remove clips. replace it with new part. Check part before replacing the top of range, if it works, the electricity can be turned back on. Repair done.

Video said to remove screws and lift stove top off, remove contacts and ground. My stove top was hinged and required me to lift and pivot stovetop up. The burners were anchored to the stove base not the top. I secured the topso that it would not drop down and proceeded with repair

Two screws to remove glass top. 2 connectors to remove. Removed glass top and put it upside down. Remove 4 wires and 2 Phillips screws. Reverse steps.

It was alittle difficult at 1st to remove the clips that held in the socket. But once out everything went smoothly.

Wanted third oven rack. No problem.

There is a good video on YouTube that shows exactly how to replace the bake element. Had mine fixed in 15 to 20 minutes. Saved me about $150 by not having to call repairman.

very expensive to buy the part but just tighten the screw intot eh predefined place.

Watched the video and realized this was something I could do myself...bear in mind I'm not exactly a handyman! Took me about 30min as the oven also needed some cleaning...my tenant definitely needs to use the self-cleaning!

I have to note, although the heating element was covered by Maytag's 10yr limited parts warranty, I deci ... Read more ded to purchase from PartSelect since Maytag could not provide a ship date and I couldn't keep my tenant waiting! Supposedly Maytag had the part in stock but their warehouse was behind because of the pandemic...what a lame excuse! Almost a month later, Maytag has yet to ship the part! Needless to say, am very disappointed in Maytag's after sales and warranty program! I get the impression, they just wanted to pressure me to buy the new part!

Lastly, was very pleased and impressed by PartSelect's customer service! Their website was very easy to use, less expensive than buying direct from Maytag and the part was shipped same day! Thank you PartSelect!