Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Dryer would not start
12 of 14 peoplefound this instruction helpful.
Kenneth from COATESVILLE, PA
Really Easy
15 - 30 mins
Screw drivers
I popped the door switch out with a small screwdriver, disconnected the electrical connection and re-connected the new switch and popped the new switch in place with a little adjustment.
Was this helpful?
Thank you for voting!
The old filter had holes in it
10 of 11 peoplefound this instruction helpful.
Robin from CANTON, OH
Very Easy
Less than 15 mins
No repair, just replace the old with the new. Fast delivery.
Was this helpful?
Thank you for voting!
dryer would not stay on so I ordered a button, but wrong part.
17 of 33 peoplefound this instruction helpful.
Linda from FITCHBURG, MA
Really Easy
1- 2 hours
First I called to get help with the right part and they told me I needed the pus-to-start-switch. It came in and I called my handyman Ed to install it. I am happy with your service. I dont install but just got the part in.
Was this helpful?
Thank you for voting!
Heat deflecter coated with plastic from drying plastic table cloth.
11 of 15 peoplefound this instruction helpful.
William from BREVARD, NC
Easy
1- 2 hours
Pliers, Screw drivers
Advice from others with same problem on your web site was very helpful. I removed one of the three torx screws holding the deflecter, Used 2.5 star-drive screw diver bit and cordless drill/driver. Replaced 2 of three torx screws holding the deflecter with the headless brass screws, Using vice grip to tighten. Removed third torx screw a
... Read morend removed old deflector. Used shop vac to clean behind it. Installed new deflector, sliding it over the 2 headless screws, then installing one of the torx screws, then replacing the brass screws with original torx screws, one at a time.
Read less
Was this helpful?
Thank you for voting!
The lent filter was worn out, the screen was ripped and torn from west.
8 of 9 peoplefound this instruction helpful.
Bruce from OKLAHOMA CITY, OK
Very Easy
Less than 15 mins
Very simple and easy it took no more than 10 seconds if that long. Remove the worn out screen (pull up and out), replace it with the new screen( slide it into the area where the old screen was removed. (No tools needed)
Was this helpful?
Thank you for voting!
DRYER WOULDN'T START
12 of 21 peoplefound this instruction helpful.
GLENDA from BLNG SPG LKS, NC
Very Easy
Less than 15 mins
Screw drivers
My dryer knob broke on the timer cycle switch so I ordered a new one along with a new dryer knob which didn't fix the problem, then I ordered the start switch and all I had to do was remove the back of the dryer where all the knobs are located and remove the start switch by turning the start switch to remove it, replace it with the new o
... Read morene by turning it till it clicks in just like when you removed it, put knob back on the front. However that didn't fix my dryer either so I ordered the thermal fuse and switched it out and that was what started the dryer back up. It is located on the back all the way to the bottom where the electrical cord is. Remove the cover and locate the fuse. Use a pair of pliers to pop it out and push the new one back in.
Read less
Was this helpful?
Thank you for voting!
belt was broken.
8 of 9 peoplefound this instruction helpful.
robert from phenix city, AL
Really Easy
30 - 60 mins
Nutdriver, Wrench (Adjustable)
remove top of cabinet and front panel. placed belt around drum and replaced idler pully placed new belt around pully and was done. not a hard job at all. replced front panel and top. thanks to a speedy delivery of my parts dryer was only down two days.
Having 2 persons make the job easier. 1) Remove the screws that holds the hinge to the body of the unit. 2) Remove the screws around the door so you can get to the hinge. 3) Remove bad hinge and replace with new one.
Was this helpful?
Thank you for voting!
Torn screen on lint filter
6 of 6 peoplefound this instruction helpful.
Elizabeth A from STEVENS POINT, WI
Very Easy
Less than 15 mins
Just put new lint filter in slot I had torn the screen on the original one
Was this helpful?
Thank you for voting!
The plastic knob broke off inside the turner
6 of 6 peoplefound this instruction helpful.
Teresa from WINK, TX
Very Easy
15 - 30 mins
Screw drivers
Unscrewed the top back of dryer and replaced the unit 1 wire at a time also was easier due to the letters besides the wire
Was this helpful?
Thank you for voting!
The Lint filter in the dryer was damaged from continuous use.
6 of 7 peoplefound this instruction helpful.
Mary Ann from SUN CITY WEST, AZ
Really Easy
Less than 15 mins
I just popped in the new Filter and it fit perfectly. This will prolong the dryer use, looks like new.
Thank you Part Select.
One Happy customer
Was this helpful?
Thank you for voting!
Needed a shoe rack
5 of 5 peoplefound this instruction helpful.
Scott from NOVATO, CA
Very Easy
Less than 15 mins
Lift the lint filter and slide the 2 hooked ends into the 2 holes provided . Front end is locked in as other end is suspended .
Was this helpful?
Thank you for voting!
The dryer drum wasn't spinning, but I could hear the motor and feel the heat from the heating element.
5 of 5 peoplefound this instruction helpful.
David from LAWRENCEVILLE, GA
Really Easy
30 - 60 mins
Screw drivers
UNPLUG the dryer. I removed the top panel by removing the two screws at the top of the dryer door. There are some hooks toward the back of the top panel, so you'll need to slide it to the left to get it off. The front panel needs to be removed by removing two screws just inside the top left and right corners. Lift and set it aside. I didn
... Read more't disconnect the door wiring, but you can if you need to do so. I just spun the front panel to the left and out of the way. With the drum exposed, I confirmed the belt was broken. I replaced the belt, then the front panel and top panel. While I was inside the dryer, I did a through cleaning with the vacuum to get all the lint.
The video on the site is easy to understand and a snap to follow.
Read less
Was this helpful?
Thank you for voting!
Noisey squeaking noise.
5 of 5 peoplefound this instruction helpful.
Lewis from WESTFIELD, NJ
Really Easy
1- 2 hours
Screw drivers, Socket set
Replaced the rear drum bearing, Front drum bearing,front bearing tabs and belt. I replaced the belt from the front of dryer. Better to go thru the back. Much easier.
My Orders
