HTS18ICSVRCC Hotpoint Refrigerator - Instructions

put the gratefruit knife behind the old switch pooped it out pluged the new one in piece of cake 5min.even vacumed the dust off the coil

This was so easy I think it took me 2 minutes. I am not very mechanically inclined but that didn't matter! Works perfect thank you!

Simple. Remove part from wrapping and box, snap into place on door. All of one minute.

Remove the top cover above the door by lifting it slightly and pulling forward. I used a mirror to make sure that there was nothing in the way of accessing the switch from above. I used a blade screwdriver to press against the switch retainer on the topside, while GENTLY prying from below with another blade screwdriver to get the switch d ... Read more islodged. Once the retainer was past the opening, I wiggled the switch downward and then rotated it to the left when the rounded top right edge of the switch was visible. This allowed the wiring to the connector to pass thru the hole. I pushed the wiring from the top and pulled from below to get the connector below the opening for the switch. I then unplugged the switch, plugged in the new switch and reversed the removal process feeding the connector thru first then rotating the switch to the right to get the rounded edge of the switch thru the opening, then pressed the switch up into the opening until it snapped into place. Total time less than 10 minutes.

Unplugged refrigerator Removed the cover in freezer compartment
Removed old thermostat and installed new
Replaced cover and plugged in refrigerator

Remove the one screw holding the unit in place, unplug it, slide in the replacement, plug and screw it in.

removed back cover--disconnect water supply-- removed screw holding vave and unplugged the
electric from the valve-- disconncect waterline to
the icemaker. reverse the to put on new part.

0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
... Read more />3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.

with a jewelry screwdriver I pried the lock tab in and pulled switch down carefully, the hardest part was that the power wire connector was stuck on good but the pliers and the jewelry screwdriver was its match for a bout 5 minute for one connection a simple pull off prong connection. After the wire connected back to switch it popped back ... Read more in SNAPP

Pop out switch, pull wires, attach wires to new switch and pop back in. Easy smeasy!

Removed old valve easily. New WR57XI0033 valve is designed to mount on lower left, but on mine it has to mount on lower right. Had to drill two 1/32 holes in lower rail to mount the new valve.

Had to defrost the freezer to melt off all the ice before servicing. Once that was done the icemaker replacement only took about 15-30 minutes to complete. The new icemaker came with many accessories and adaptors that were not needed and the instructions were based on replacing an older model and not really clear for my model. They men ... Read more tioned not being able to use the new stripper but it was exactly the same as the old one so I left the new one in place. All in all it was easy and did the job.

I didn’t do the repair because I ordered two grommets. When they arrived, one of the packages was empty! Instead of just sending me another one, they refunded the part so I still need one. By the way, I was not refunded half the shipping either which was more than the part itself.

Looked at fan and seen it was rubbing metal cage. After looking and checking fan noticed bushings were worn letting fan hit cage. Repair was very easy. Used a 1/4 inch nut driver to remove bracket holding fan. Pulled fan blade off shaft by just pulling it forward. Removed fan and replaced grommets. Reassembled fan and fan blade. Took ... Read more just 10 minutes.

removed screws holding back plate removed air devise pul slightly out lift straight up and ou remov 2 screws in the fan cage remove ice maker 2 screws and a plug in connector.pull back fram slowly forward angle to the left remove.you'll see condenser in front of you.thermostat is to the right attached to top coil of condenser clips on rem ... Read more ove.two wires cut close to old thermos and remove install new one make sure back which is plastic faces you.attach wires with wire nut or inline #14 slices.just go in reverse to finish. maakesure you unplug fridge first and of course plug her back in.wait 24 hours for everything to settle down.