HTS18GCMBRCC Hotpoint Refrigerator - Instructions

Removed the old water valve from back of refrigerator by using a screwdriver. Pulled water line off old valve that runs into the fridge and inserted it into the new part. I used a pair of pliers to take off water line that runs into the water valve from the house. Screwed the water line back onto the new valve. Took about 10 minutes.

thats what I did is remove the teo screws and took the old single outlet valve out. And put the new one in and put the screws back in. First turned off the water and put the water back on after I was threw and no leaks.

I'm not a DIY-er, and wasn't sure a 20 year old refrigerator was worth the repair, but for $30 I could afford to be wrong. The swap is pretty intuitive, especially in my case since the problem was that the water tube from the valve to the ice maker had detached from the coupling. So I didn't have to cut anything off, just inserted the ... Read more tube into the new valve. Reconnected the supply line, screwed the assembly back on the refer, and Bob's your uncle. Other than unloading some canned goods to lighten the refer, longest process was finding the right size nut driver in my disorganized tool tray. Be aware, there are NO instructions included with the part. Found a good video on you tube that confirmed the obvious. Glad I took a shot!

replaced lights in refrigirator and freezer

I pulled off the plastic strip that says “ vegetables” on one side “fruit” on the other. That exposed screws on the left and right sides. I unscrewed both sides I did the same to the back support arm put the new arm in and it works great! The man who helped me at part select was so patient and so kind and helping me select the right piece ... Read more to begin with to make sure I had the right model number. Could’ve had a better experience with the repair company. Tammy Peterson

Installation could not have been easier!

Removed fan housing from top of freezer, then the two screws holding the rest of it in place. Then two more screw and removed the vertical housing in back of freezer. two more screws and I was able to remove the whole back plate. I unplugged evap motor wire from back of freezer wall and unscrewed motor bracket. once motor was free, I remo ... Read more ved the blade, unscrewed ground wire and installed new motor. I then plugged wire back in to ensure new motor worked and put everything back. Super Easy!!

Pulled the fridge from the wall. Then shut the water line to the fridge off. Pulled the water line to the ice maker out the old grommet. Then a screw or two from the cover over the bottom back of the fridge, so I could get to the outlet valve kit. Only 1 screw was holding that. Then took the lines off the old outlet valve. Took the little ... Read more hose off the grommet on the inside of the freezer that leads the water into the drip pan to the cube tray of the ice maker. Then grabbed pliers for the grommet on the top back of the fridge. And pulled and twisted alittle till it came out. It was alittle hard but got it out. Cleaned the out sticky tape off around the hole where the grommet connects. Hook the water like that goes to the grommet for the ice maker to the new grommet. Peeled the paper of the sticky tape for the new grommet. And placed it in. Then connected the rest of my water lines to the inlet valve. Put everything back the way it was. Then plugged and turned the water back on. And in 2hrs or so I had ice fall in the tray and continues to make ice no problems. “Note also I didn’t actually unplug my fridge I did it all why it was plugged. Thought it would be best to let you know. LoL but a small socket 1/4 with a 1/4 drive or worked. Also I think my grommet was harder to get out cuz it was froze due to the water leaking in the grommet.

First removed the two screws that holds the old ice maker in place. Unplugged it. The freezer compartment was too narrow to allow the unit to slide out or turn in any other direction. Had to also remove the two front screws from the left side ice bin track and swing it down. The door opening was also too tight. Scratched the plastic ... Read more door jamb putting the new unit in but other than that all is well and functioning well.

Remove ice maker out of fridge; remove 3 screws
replace defective part re-install all components 30 minutes later " magic ice again. Very easy repair most important low cost. Thanks "Parts Select"

Turned off the breaker to the fridge because I couldn't reach the power plug to unplug it . Use small flat head screwdriver to pop out the piece, disconnected the rubber prong connectors, inserted the new piece into the rubber prongs snapped it back into place. Flipped the breaker back on and prayed it worked. It did and I saved myself $ ... Read more 120 service call.

Three easy steps, take off old part then all you do is tighten nut on one end of part and then just push other end of pipe down in slot. Did half to remove nut off the top end of tube very simple to do

I watched the video online, followed the instructions and within minutes had the part installed. The frig light was working once again! I will say the original switch was very snug and I had to do some very minor scraping of the plastic to get the new part to slide in.

Remove the rear cover, shut off the water, removed the hose, unplugged the electrical connector, removed the screw holding the valve on. Removed the plastic tube going into the freezer and reversed the steps

easy - replaced it

i am totally impressed with your company how effective it is.... i will go to yours if anything is broken or replaced

thanks