- Home
- HTS18BBPVRCC
- Instructions
HTS18BBPVRCC Hotpoint Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Light went out in refrigerator
1 person
found this instruction helpful.
-
Gary from EAST JORDAN, MI
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
Pop out switch, pull wires, attach wires to new switch and pop back in. Easy smeasy!
Was this helpful?
Thank you for voting!
Light Switch Not Working - Needed New Switch
1 person
found this instruction helpful.
-
Joe from SUGAR LAND, TX
- Really Easy
- Less than 15 mins
-
Screw drivers
Remove the top cover above the door by lifting it slightly and pulling forward. I used a mirror to make sure that there was nothing in the way of accessing the switch from above. I used a blade screwdriver to press against the switch retainer on the topside, while GENTLY prying from below with another blade screwdriver to get the switch d
... Read more
islodged. Once the retainer was past the opening, I wiggled the switch downward and then rotated it to the left when the rounded top right edge of the switch was visible. This allowed the wiring to the connector to pass thru the hole. I pushed the wiring from the top and pulled from below to get the connector below the opening for the switch. I then unplugged the switch, plugged in the new switch and reversed the removal process feeding the connector thru first then rotating the switch to the right to get the rounded edge of the switch thru the opening, then pressed the switch up into the opening until it snapped into place. Total time less than 10 minutes.
Read less
Was this helpful?
Thank you for voting!
40 year old refrigerator brittle light switch fell apart
1 person
found this instruction helpful.
-
Loren from EL PASO, TX
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
with a jewelry screwdriver I pried the lock tab in and pulled switch down carefully, the hardest part was that the power wire connector was stuck on good but the pliers and the jewelry screwdriver was its match for a bout 5 minute for one connection a simple pull off prong connection. After the wire connected back to switch it popped back
... Read more
in SNAPP
Read less
Was this helpful?
Thank you for voting!
Noisy
1 person
found this instruction helpful.
-
Brad from SPRING MILLS, PA
- Very Difficult
- More than 2 hours
I didn’t do the repair because I ordered two grommets. When they arrived, one of the packages was empty! Instead of just sending me another one, they refunded the part so I still need one. By the way, I was not refunded half the shipping either which was more than the part itself.
Was this helpful?
Thank you for voting!
Freezer was cold but fridge was warm. Coils in the back of the freezer were getting frosted. Defrost Sensor was broken
1 person
found this instruction helpful.
-
Kevin from Charlotte, NC
- Easy
- 30 - 60 mins
-
Socket set
-Empty the freezer
-Take the cover in the back of the freezer off
-Melt the ice off the coils (heat gun, hot water, etc.)
-Cut the wires off the old sensor and connect the new sensor using a soldering iron or some other method.
-Cover the spliced wire with heat shrink, electrical tape or some other method.
-Reasse ... Read more mble the cover
Done!
-Take the cover in the back of the freezer off
-Melt the ice off the coils (heat gun, hot water, etc.)
-Cut the wires off the old sensor and connect the new sensor using a soldering iron or some other method.
-Cover the spliced wire with heat shrink, electrical tape or some other method.
-Reasse ... Read more mble the cover
Done!
Read less
Was this helpful?
Thank you for voting!
Had a 'ticking' sound
1 person
found this instruction helpful.
-
John from PARKVILLE, MO
- Easy
- 30 - 60 mins
-
Socket set
Separately (from a different site) purchased new compressor fan and motor. I purchased the grommets here because the other site listed the grommets as temporarily out of stock. I did watch one of the videos on PartSelect about the grommet replacement. Repair was pretty simple, biggest challenge was getting to the screw on the far side o
... Read more
f the motor. Removed the two screws holding the fan motor into place. Removed motor and blade. Reinstalled with new fan blade, new grommet and new motor.
Read less
Was this helpful?
Thank you for voting!
Light was flicking
1 of 2 people
found this instruction helpful.
-
Stephanie from KEARNY, NJ
- Really Easy
- Less than 15 mins
-
Screw drivers
It was way to ez to install only a couple of minutes that's it
Was this helpful?
Thank you for voting!
Broken light switch
1 of 2 people
found this instruction helpful.
-
Ted from SANDWICH, IL
- Easy
- 15 - 30 mins
-
Screw drivers
took a little more effort than the video show to remove old module and replace new. Works fine now.
Was this helpful?
Thank you for voting!
Change bulb
3 of 8 people
found this instruction helpful.
-
Louis from LEAGUE CITY, TX
- Really Easy
- 30 - 60 mins
-
Nutdriver
Easy
Was this helpful?
Thank you for voting!
The door activated light switch was missing.
1 of 3 people
found this instruction helpful.
-
Don from Eugene, OR
- Really Easy
- Less than 15 mins
Pulled the two wires out from the access hole in the lower part of the refrigerator. Put them in the spade connectors on the new switch, and pushed the switch into place.
Was this helpful?
Thank you for voting!
Fan stopped working, Ice maker burned out
0 of 1 people
found this instruction helpful.
-
TODD from PLAINVILLE, CT
- A Bit Difficult
- 15 - 30 mins
-
Nutdriver, Screw drivers
Fan Quit So did the Ice Maker. $150.00 worth of parts plus my time. Also the Freezer Floor cracked for some stupid reason.
Other Parts Used:
Was this helpful?
Thank you for voting!
Bad switch for door prevented interior light from coming on
0 of 1 people
found this instruction helpful.
-
Patricia from Sylva, NC
- A Bit Difficult
- 15 - 30 mins
-
Pliers, Screw drivers
Just as your video described, although due to the age of the fridge, it took a bit longer to remove the defective switch. Your video made this so simple, I can't imagine why we lived with a dark fridge for so long! I was ready to buy a whole new fridge, as repairmen are often nonexistent for small repairs. I am the biggest fan of yo
... Read more
ur company & it's repair video. THANK YOU SO MUCH
Read less
Was this helpful?
Thank you for voting!
The evaporator fan in the freezer compartment began making a loud noise.
0 of 1 people
found this instruction helpful.
-
Boyd from Rapid City, SD
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
I found a replacement evaporator fan motor and 2 mounting bracket grommets at PartSelect.com at a reasonable price. I watched the installation video provided and installed the new parts as shown in the video start to finish installation time 22 minutes.i
Was this helpful?
Thank you for voting!
Light burnt out.
2 of 8 people
found this instruction helpful.
-
Roscoe G from ROCHESTER, NY
- Very Easy
- Less than 15 mins
Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.
Was this helpful?
Thank you for voting!
Cracked Dairy Door
0 of 3 people
found this instruction helpful.
-
Fr Kerry from Washington, DC
- Really Easy
- Less than 15 mins
PartSelect shipped me the part and it arrived in less than 3 days. It took longer to unwrap the excellent packing than it did to pop the new door into place. Wonderful!
Was this helpful?
Thank you for voting!