HTF16BBMERWW Hotpoint Refrigerator - Instructions

I pull the old one out, and put the new one in.

assembled ordered parts then replaced defective fan and blade and bracket as a group

Unplug. Remove back cover. Remove retainer (simple wire clip) from overload. Unplug overload from compressor. Remove two power wires (if stabs are tight you might need pliers). Note which wire goes where. Remove capacitor from overload (just pul it straight out .. Pull hard or pry a little with screwdriver. Insert capacitor into new switc ... Read more h. Reattach wires to same place in switch. Insert switch into compressor. Replace retainer clip. Replace rear cover with original screws. Plug in. Cool!

Removed freezer cover, removed fan and fan motor, and bracket holding the fan moter. Installed fan, installed motor and wa-laugh, done.

I noticed that if I unplugged the refrigerator and plugged it back in a while later it would start working but eventually would stop. I deduced the problem was likely the defrost thermostat. I ordered the thermostat but it was in a difficult place behind the evaporator coil which I could not remove. While I was trying to work it into posi ... Read more tion my hand pressed against the defrost coil and shattered the glass sheath. I ordered the coil and finally managed to get it and the thermostat installed. The refrigerator seems to work fine now.

Removed two screws holding the cover. Unclipped and unplugged the defroster timer. Plugged in the new one . Replaced the cover. Finished.

After looking at our broken bottom shelf in the fridge many times a day for over a year, I finally got around to doing something about it. So glad that I did! First of all, the part was shipped amazingly quickly. I had it within two days (at regular shipping). Secondly, it was a cinch to install. What a world of difference!
The only ... Read more caveat is that the new shelf fits quite snugly. If you don't give the refrigerator door an extra push to close it, the door does not seal. Just a new habit we have to get into.

I did folllow the instructions on the video step by step.

common sense,removed plate,removed mounting bracked,unplugged,reversed order,and that was it.

Removed freezer bottom and back plates-encountered ice -melted with heat gun.Observed fan not running with fridge plugged in and considerable erosion of the styrofoam part.ordered fan motor and blade and styrofoam ducting and replaced same.Fan started running immediately when plugged in and now the compressor cycles normally and the refri ... Read more gerator compartment is much cooler and icing has stopped. I'm good to go until the compressor fails! thanks for the excellent delivery service(2 days)and your parts diagrams really helped me trouble shoot the problem.

At this time of the year our beach fridge is always full of food and drinks. Every time we want something it meant leaving the door open for extended time whlie moving things left, right and center. When the new shelf arrived I removed the food and drinks from the existing two shelves and moved them closer together. I then slipped in the ... Read more new shelf and reloaded the food. Suffice to say the fridge stays open less and we are able to get at things without moving others. I wish I had thought to do this before.

I had lost the bottom hinge during a move and so I rigged the hinge using an old tv antenna and the door never really quite worked right and it was VERY annoying. I stumbled upon this site and was surprised how inexpensive the part I needed was. I was very impressed with the speed of shipping and the install took maybe 5 minutes. The f ... Read more ridge works as good as new. Thanks a ton!

4 screws in the freezer and the back panel came off then 2 more screws to take the motor off. I unpluged the old motor pluged in the new motor put the back panel back on and I was done.

I used pliers to pull lightly on the head of the switch, while I inserted a small flat head screw driver into the base of switch and gently worked around the edges to free it from the panel.

I replaced the fan motor and one of the grommets. When I took the motor out it was clear it was failing because there were metal flakes from the motor on the fan blade. I followed the instructions on the posted video. My model did not have a removable bottom tray in the freezer so that was one less thing to do. Aside from that the vide ... Read more o was accurate. I had two minor problems during reinstallation. First, it was very difficult to get the spring clamp back on the fan blade without pushing it against the motor. Recommend you get someone to help hold the spring open while you push it on. Second, the length of wire on the replacement was not exactly the same as the original and I had to move some wires around. Recommend you take a picture of the cable layout before disassembling.