HTDX100GM7WW Hotpoint Dryer - Instructions

After unplugging the dryer, I removed 2 metal screws up under the dryer sill rim, and removed the dryer top. Then, removed two more at the top of the front (door) section to remove it.

I wasn't careful enough when removing the door, and the wiring connectors popped loose from their connections. No harm done, though. Disconne ... Read more ct the wires once you remove the front panel.

I had to loosen the bottom metal screws on one side panel to have enough give to pull the dryer drum out.

The only way to replace the belt is to bend over the side of this unit and with one hand put the belt around the motor drive shaft, pull the tension pulley back, and put the belt on the wheel.

The hard part is working the drum back into place while VERY carefully slipping the belt into the drum goove. Many attempts were made only to have the belt slip off of the tension pulley or motor driveshaft. Be care full to turn the drum clock wise if the belt twists while working it into the drum groove. It was very disappointing to finally get the belt on, and work the drum back into place only to discover I had twisted the belt with the smooth side making contact on the driveshaft. Thus, I started over.

Aiming the drum into the back of the dryer is a tough task. I recommend a 1" X 4 " X 12" board to slip under the drum when beginning this process to help stablize, and guide the drum. It helped me tremendously, and was easy to remove out from under the drum once everything was back in place.

Use gloves. Yes, tough to work with in small places, and I did take them off to replace the belt around the tension pulley, however, there are too many sharp edges on the metal body of the dryer and especially the drum to do so without gloves.

Wires were easy to reattach and reassembly was smooth except for the top...check out the tabs, and spring tabs before you try and just plop the top back on. It goes a certain way...You'll know what i am talking about when you do this task.

I truly hope you have L O N G arms to do this task, and that the new belt lasts a long, long time!

Replaced dryer motor which was a perfect fit thanks to your help. The process was helped by the internet videos available for the step by step procedure of taking the dryer apart and replacing the bad motor. I also was able to completely clean the inside of the dryer thoroughly, and reassemble it back together .

Ordered & received new Timer & Knob. Disconnected dryer from power.
Located screws on back of dryer console & removed screws so console could be tilted forward.Used cell phone to take picture of timer with connections to keep track of where to reconnect wires. Unsnapped connections to timer. Removed old timer and attached new ti ... Read more mer. Attached new knob to front of console. Plugged dryer back up to power and tested by turning new knob. Reattached console with screws. Done!

Once I figured out how to remove the control panel. The rest was very easy. Upon pulling off the knob in the center of the control panel, there was a screw behind it. Once removed I used the palm of my hand and gave it a couple of upward hits in the center while the door was open. It slid up and I removed the electrical connections. Then ... Read more carefully removed the top by pushing from the rear of the machine slightly and lifted off. Then removing the screws that hold the front on . After that it went pretty easily, reassembly went in reverse and. That was that!

We watched the YouTube video and had it installed in no time. Saved money doing it ourselves.

Exactly how your perfect video instructions showed me. Thank you for a job well done!

Called my son-in-law. Easy as pie

When I ordered it in the email receipt were directions- just click installation instructions- I also looked at u tube video by just typing in GE Dryer timer repair. It took longer to clean the floor where the dryer sat for years since we never move it. Cleaning time is included in the 15 minutes— You will feel great since just saved a to ... Read more n of money. So glad I found you for future issues with appliance repair. There are U Tube videos to fix everything. Robert Maheu Huntington Beach

I followed the Youtube video created by PartSelect and it was SUPER easy.
Removed dial from front panel
I unscrewed the back panel, which released the knob panel on the front and tipped that forward to access the timer device.
Released the locking tab and spun the entire timer counter clockwise until it released. Pulled ea ... Read more ch connecting wire off and immediately replaced it on the new timer so I didn't mix up the order.
Once wires were attached, I replaced timer turning clockwise until it locked in place.
Re-positioned front panel and replaced back panel installing screws.
Replaced dial and dryer was ready to go!

TOOK OFF TOP AND FRONT PANEL REACHED IN UNDER TUBE AND REMOVED FROM BELT TENSIONER HARDEST PART IS PUTTING BACK ON TENSIONER TAKES TWO HANDS LAYING ON YOUR BELLY

loosened two hose clamps and four screws to replace the anti siphon valve.

Well, the intall would have been great except for the fact that I needed another part. If your belt breaks there is a reason for it. Make sure you check all the parts that work with the belt. Their was a pully the was defective and also need to be replaces. I think it would be a good idea to put a little note on the page for the Belt Driv ... Read more e to let people know that if you are replaceing the belt you might want to check the Idler Pully for it too might need to be replaces. I'm not an expert and if that was on the page for the Belt Drive I might have look at the pully before I ordered and I would have ordered the part along with the Belt Drive. As it was had to wait another 4 day to get my dryer fixed. I'm very happy the Parts Select has all my parts and they pretty good at getting them out to me in a good amount of time when I need them.

Un plug the dryer. Gather phillip, flat head and torix screw drivers. Remove the rear of the dryer to get the spec sheet with the appropriate part number. Next called for part. Belt installation requires removal of front and top of dryer in order to slide belt over the drum. Getting to all the fastners requires tilting the dryer on its ... Read more back. Clean out excess lint from dryer interior and duct work. Slide drive belt over drum and use some masking tape to hold it in position. Reassemble dyer. Return dryer to upright position and put the belt on the pully and tensioner from rear access port. Remove tape. Replace access panel. Reattach vent duct work. Plug in. There are 5-6 different size screws holding everything together...you may want to use masking tape to label where each type of screw goes. All totaled it took about an hour and cost less that $25. Well worth the effort.

Simply pull old knob off..slip new knob on. Less than 2 seconds...done

Pull the old lint trap out. Slid new one in