Home
HTDP120GD4WW
Instructions

HTDP120GD4WW Hotpoint Dryer - Instructions

All Instructions for the HTDP120GD4WW

Old timer Knob cracked where clip goes.

27 of 27 people found this instruction helpful.

Kenneth from OCALA, FL
Very Easy
Less than 15 mins

I did a search on your site to find out why dryer wouldn't start. It said 25 % of the time it could be the timer knob. Checked my old one sure enough it was cracked.Took old timer knob off and pushed New one back on less than a minute. Thank you for your site. It saved me from costly repairs.

Was this helpful?

replacement of holed lint screen

30 of 41 people found this instruction helpful.

Mark from Clarksville, VA
Really Easy
Less than 15 mins

straightforward swap, just form the top rail and click it in

Was this helpful?

dryer was cutting off completely.

32 of 50 people found this instruction helpful.

Stephen from Mechanicsville, VA
Easy
15 - 30 mins
Screw drivers

The problem was intermittent. It only happened when the unit was first started. After it was restarted it usually worked until the load was dry. I looked at the schematics and saw that only the hi-temp therostat and the motor overload could stop the dryer completely. I put my volt meter on the hi-temp thermostat and ran the dryer. Wh ... Read more

Read less

Was this helpful?

interlock switch was bad. Prevents the dishwasher form running as it "thinks" the door is still open.

31 of 52 people found this instruction helpful.

Steven from EPHRATA, WA
Very Easy
Less than 15 mins
Nutdriver

Opened door, removed screw holding down metal plate that presses against interlock switch when door is closed. Removed plastic cover thingy that is over interlock switches. Removed the interlock switch by pressing the plastic lock thingy away from switch. Pulled the wires off each end of the interlock switch. Removed new interlock switch ... Read more

Read less

Was this helpful?

Noisy like a chain rattling inside

27 of 43 people found this instruction helpful.

Kerry from New Martinsville, WV
A Bit Difficult
30 - 60 mins
Pliers, Screw drivers, Socket set

Disconnect Power from the Dryer
Remove 2 screws that held the top on the dryer.
Removed the 2 screw that held the front on the dryer.
Unhooked the belt from the tensioner and motor pulley.
Pulled the drum out. Removed the belt.
Removed the three screws that held the bearing assembly
on the back of the drum. ... Read more r />Removed the keeper o-ring slide the bad bearing off of shaft. Slide the new bearing on the shaft put the new o-ring on the shaft. Reassembled the bearing on back of the drum. Put belt back around the drum and put drum back in place. Put The belt around the motor pulley and tensioner
(this is probably the hardest part).
Put the front and top back together.
Turned the power back on. Job done
Read less

Other Parts Used:

Drum Bearing Sleeve

Retainer O-Ring

Bearing Retainer

Was this helpful?

Thank you for voting!

Needed to change the door opening position

24 of 36 people found this instruction helpful.

Robyn from Laguna Niguel, CA

Really Easy

Less than 15 mins

Screw drivers

I removed the door and "flipped" it to open right to left. Rather than remove the existing door latch I added the purchased latch on the right side to enable opening the door right to left or left to right.

Was this helpful?

Thank you for voting!

Horrible screeching noise when the dryer drum was in motion, cracked pieces were tangling and ripping the drying clothes.

28 of 49 people found this instruction helpful.

MonaLisa from Bronx, NY

A Bit Difficult

15 - 30 mins

Screw drivers

I removed the top of the dryer (unscrewed from the inside to release the top). Removed interior screws to pull open the front of the dryer. Once inside, it was really visible that the old parts (front air duct top and bottom) were in bad shape. They were cracked and broken. I removed the old pieces (they pretty much cracked and crumbled r ... Read more ight off). I snapped in the new pieces careful to avoid damaging the electrical connections and wires. Once snapped into place (top and bottom), I careful put the front back into place making sure that the dryer drum rested on the new pieces. All screws back in place and all done! Dryer is now working as new!!!
Read less

Other Parts Used:

Lint Filter - White Frame

Dryer Lint Chute Assembly

Was this helpful?

Thank you for voting!

door latch was broken

20 of 26 people found this instruction helpful.

Kate from MULLINS, SC

Really Easy

Less than 15 mins

Pliers

Pulled out the remnants of the old latch out with the pliers and then popped the new one in...less than 2 minutes. Oh, and the part was delivered in less than 2 days. Great job, Partselect !

Was this helpful?

Thank you for voting!

Door handle broken

19 of 24 people found this instruction helpful.

Jennie from Louisville, GA

Really Easy

Less than 15 mins

Inserted handle into slots

Was this helpful?

Thank you for voting!

Overheats,(timer doesn't move) on auto cycles, works ok on time dry.

17 of 18 people found this instruction helpful.

Howard from COVENTRY, RI

Really Easy

30 - 60 mins

Screw drivers

Replaced cycle thermostat.

Was this helpful?

Thank you for voting!

My dryer knob broke.

16 of 16 people found this instruction helpful.

Zelda from MARIETTA, GA

Very Easy

Less than 15 mins

Pliers

I simply removed the small black piece and inserted the new knob and it was ready to work. It was so easy and I am very happy. I though I was going to need a repairman but I was able to do it myself. Also, the ordering and delivery was fast and easy!!!!

Was this helpful?

Thank you for voting!

broken knob that turned too freely and did nothing

17 of 19 people found this instruction helpful.

Terri from DADEVILLE, AL

Really Easy

Less than 15 mins

I wasn't sure that a new knob/clip would fix problem b/c shaft wouldn't turn with pliers. But knob was so inexpensive I wanted to try it first. I received the new knob/clip and the dryer worked perfectly; the knob had been broken for a year before it had quit working entirely. Don't let someone tell you that you need a whole new timer bef ... Read more ore you try the new knob/clip. Still working perfectly and I'm so pleased. And my part arrived within 2 days-wonderful!
Read less

Was this helpful?

Thank you for voting!

new lint filter

20 of 29 people found this instruction helpful.

william from simi valley, CA

Really Easy

Less than 15 mins

my problem was easy, i orderd a new lint filter, for a
dryer that is at least 10y/o. it came to me by FEDEX,
in 3 days. i threw out the old one and put in the new
one. easy peasy. i will say that this website had what i
wanted and got it to me very quickly. good job by
PARTSELECT......

Was this helpful?

Thank you for voting!

Dryer Overheat & Shutoff

16 of 18 people found this instruction helpful.

Gary from MARTINEZ, GA

A Bit Difficult

1- 2 hours

Screw drivers

I reviewed the video instructions on the website; these were invaluable to understand the task. Since the dryer drum had to be removed to replace the thermostat, it was prudent to replace the drive belt at disassembly. Great job on the videos to see the extra effort required to install the new belt around the tensioner pulley while sup ... Read more porting the drum. I will use this site again when a need arises, because they are quick to ship the ordered part(s) and help the DIY handyman make repairs via the videos.
Read less

Other Parts Used:

Drive Belt

Cycling Thermostat - 4 Wire

Was this helpful?

Thank you for voting!

Door wouldn't stay shut

18 of 25 people found this instruction helpful.

Catherine from Windber, PA

Really Easy

Less than 15 mins

Pliers

When I went home at Christmas, I saw that my Mom had been using a small bench to keep her dryer door shut. I wrote the make / model of the dryer down and found your website. I ordered the part, and my sister snapped it into place. My mom was so happy to have her dryer door stay shut again!

Was this helpful?

Thank you for voting!

All Instructions for the HTDP120GD4WW

16 - 30 of 436
Prev
1
2
3
4
5
...
30
Next