HR2651 Makita Hammer - Parts

Length 8 Foot Length: 6' Gauge: 18 Wires: 2 Type: Bare Wire This power supply cord is a genuine OEM sourced replacement part. It is specially made to supply power from a standard outlet to Makita power tools. A cracked or damaged cord should be replaced before continuing to use the tool. This rubber insulated cord is sold individ...Read moreually. It comes with a rubber sleeve grommet that is not sold separately. Replacing this power supply cord you will need a screwdriver. • Remove the housing screws • Remove the the housing • Disconnect the old cord wires • Remove the old power cord • Secure the new cord in place • Connect the wires • Reassemble and test the new cord

This tapping screw is an authentic hardware that is supplied by original tool manufacturer for use with a variety of Makita power tools. It has multiple uses depending on the model of your unit, please make sure to check appropriate diagrams for correct location and use of this screw. Note this durable metal screw is sold individually.

This is a genuine manufacturer sourced replacement part designed for use with Makita power tools. It is a standard hardware which has multiple applications based on your tool. Please refer to diagram to ensure correct application. This pan-head screw is made out of metal and it is sold individually. Requires a phillips screwdriver to install or remove this screw.

Genuine Makita replacement part. Set of 2 Carbon Brushes with wire lead attached. • Worn brushes are often the cause of a poorly running motor • Replacing brushes can fix an intermittent motor • New brushes can restore a motor's electric braking Carbon motor brushes are one of the most commonly replaced power tool components....Read more Because carbon brushes are wear items, meaning that through friction and use they will gradually wear away, they will eventually require replacement. Worn brushes are common causes of intermittent motor function, reduced electric braking, and reduced motor power. A worn out brush will often be worn down near the wire lead and may be cracked, pitted, or burned. When replacing carbon brushes, be sure to also inspect your armature for burns, cracks, or other damage which indicates a larger motor problem.

This replacement pin is an authentic OEM component which is made for use with Makita equipment. The pin is generally utilized to secure a part while allowing it to rotate freely. It is a standard hardware which may have multiple applications. Make sure to refer to the appropriate diagrams of your model for the exact location and the corre...Read morect installation of this pin. One durable metal item is included. You may need a screwdriver to take the unit apart when replacing this pin.

This durable plastic latch is an original part sourced directly from Makita. This item is used to secure the drill case when closed. It is an identical replacement for a broken or missing latch that originally came with a new unit. Please see the appropriate diagram for your model to determine the correct location and application of this part. One item is included per order.

Included in Part Number 516306-1. rnThis Ball Bearing is sealed on both sides. This genuine Makita replacement part is sold individually. rnrn • Ball bearings minimize friction between rotating parts in your tool. The balls or rollers bear the load and spin, distributing the weight evenly, while the minimal contact area of the balls re...Read moreduces friction. This reduces wear on the tool, allowing it to run smoothly. rn • Bearings experience constant wear when the tool is in operation from pressure, heat, vibration and friction. Because of this, many Bearings need periodic maintenance or replacement.

This cord protector is an OEM part designed for a variety of Makita power tools. It is attached where the power cord meets the tool. This part protects the cord from damage due to pulling, bending, or other strain. This rubber cord protector is sold individually. It does not include a replacement cord.

This O-ring seal helps maintain proper internal pressure within rotary and demolition hammer mechanisms, supporting efficient operation and preventing leaks of air, oil, or grease. Made from durable elastomer material and measuring approximately 0.63 × 0.63 × 0.63 inches, it is designed to withstand heat and high-pressure conditions durin...Read moreg heavy use. Replacing a worn or damaged O-ring helps restore compression, improve hammering performance, and ensure smooth, reliable tool operation.