HPE16BTNDRWW Hotpoint Refrigerator - Instructions

Do not uninstall the old gasket until you have read all of these instructions. Upon receipt of the new gasket, compare the model number of the GE refrigerator to the paperwork included. Unpack the gasket by hand to ensure not to damage the new gasket. There is no specified top or bottom, left or right to the gasket but there is a front si ... Read more de (to the freezer face) and a back side (attaches to freezer door). Hold the new gasket up to the installed old gasket to ensure the size is identical (close in size WILL NOT work). Once the size is verified, pull the old gasket from the door, starting at any corner. The front side of the gasket is broader than the back side which presses into the door slot. Make sure that the door slot is clean to ensure a perfect fit. Recommend the new install begin at a top corner. Gently press the new gasket into the slot along the top. Do a side next, working the gasket in along the bottom to the last corner. Ensure the freezer face is clean for the best seal. Make sure the new gasket is dry, a wet gasket may freeze and pull the new gasket out! A good seal is verified by the "suction" when trying to open the door. A good seal is also indicated by no moisture/condensation the following day.

1. Order replacement board so it's on hand.
2. Unplug appliance or turn off appropriate circuit breaker.
3. Remove all items on top shelf of refrigerator to allow yourself working room.
4. Remove one phillips head screw, at front of control panel bezel.
5. Allow bezel to hang down a little so you can disconnect mu ... Read more lti-pin connector, by squeezing the tabs on opposite sides and pulling down. Note black dot on tab for easier orientation of replacement connector.
6. Gently pull the entire assembly forward to remove. It has two pins that align and hold the back of the assembly to the deck.
7. Place assembly on a table with the control board facing up.
8. Remove plastic push pin that holds protective cover over the control circuit board.
9. Remove temperature control knob by pulling straight out.
10. Push back 2 locking tabs at the front of the control circuit board so it will become loose.
11. Pry up cable tie mount that holds wire bundle to the assembly.
12. Free thermistor wire from it guides and flip over the assembly that is holding the sensor.
13. Peel up the tape holding the wire in the molded groove so wire/sensor can be removed. It is not necessary to remove the tape since you will use it again.
14. Remove the two wires that connect to the door switch at the front left of the assembly. It's a tight fit, but you can remove the spade connectors.
15. Now the circuit board assembly can be removed and set aside.
16. Optional - at this time you can use the continuity tester to verify the door switch is working properly.
17. Now install the new control board by reversing the removal steps.

I had lost the bottom hinge during a move and so I rigged the hinge using an old tv antenna and the door never really quite worked right and it was VERY annoying. I stumbled upon this site and was surprised how inexpensive the part I needed was. I was very impressed with the speed of shipping and the install took maybe 5 minutes. The f ... Read more ridge works as good as new. Thanks a ton!

Unplug refrigerator. Used nutdriver to remove screw. Lowered panel. Removed temperature knob. Slid tray forward. Unhooked light switch. Removed the temperature control cord. Popped out old board. Replaced new board in reverse order. Refrigerator repaired.

Want to thank Haley, and Steve in Parts Select, for assisting me in replacing the GE freezer gasket, which was a very EASY process, took all of two minutes! The video did help.

Empty bottom glass shelf. Remove 2 veggie bins & top glass panel.. Lift old part out place new part in.Drop glass self panel back in install veggie bins, done. 15 min not including cleaning the area.

Bent the motor bracket down, then using a rat tail file, elongated the holes in the back panel of the refrigerator to secure the fan in the "centered" position. This was a problem that was with the refrig. since it was made. The parts involved were perfect. NO problem at all installing them.

Remove ice maker and all of it's accessories in order to remove the panel covering the fan. Don't drop the screws!
Unscrew the lower fan bracket. You will see the lower red rubber grommet. Hold fan motor with one hand and push the fan off the shaft and into the compartment above. Then remove the round retainer thing below it by holdi ... Read more ng it and pulling down on the motor assembly. Install new grommet on upper part. and put it all together.
REMEMBER where the fan is on the shaft. It has about one inch of shaft placement. I put mine so that most of it was above the hole that the fan goes into and about 20 percent showing below the sheet metal.
Also check to see if your fan is damaged. Mine was not.
This refrigerator has been awesome! I have had many issues but have been able to fix all of them for the last 15 years!

I have not yet done the repair. After watching this repair video two problems came to mind. First I only ordered one grommet not knowing that there were two (or more I don't yet know). The second problem is that this video must be for a fridge from like the 1940, but it looks NOTHING like mine from 2008. The manual shows a bazillion parts ... Read more and frankly I'm just a wee bit afraid to get started, and I am generally very handy, buuuttttttttt I don't know about this one

Slide it over the fill hose and just line it up and put it in the slot.