HLT28 Homelite Trimmer - Overview

This spool retainer is sourced from the equipment manufacturer for use in trimmers. It is a plastic knob, measuring 2 inches in diameter, with a threaded metal bolt in the center. The retainer has a right hand thread, and it is used to secure the spool within the trimmer head to prevent it from coming loose during operation. The retainer ...Read moreengages with the trimmer head to lock the spool in place, while it also advances the cutting line for greater cutting efficiency. If the threads on the retainer bolt wear out or the plastic body becomes damaged, the retainer will be unable to engage with the trimmer head, causing the line to tangle, the spool to come loose, and lowering the cutting performance of the trimmer. Remove the trimmer head cover and detach the retainer from the assembly. Position the new spool retainer in the assembly and thread it firmly into place.

The OEM Air Filter is used to stop debris and particles from entering the carburetor and engine, which could cause damage. It is attached in the air filter housing. It comes in black, and is contructed from foam. Installation is rated as "Easy" by customers, and will require a screwdriver. (Tip: You can place the filter in a plastic bag w...Read moreith a bit of oil, remove it, and then squeeze the filter to drain the excess oil. The remaining oil will work as a sticky trap). If the part becomes worn over time, the engine will be hard to start and will run rich. In this case, replace the part. Refer to your make, model and diagram to ensure this is the correct part for you.

This is a genuine OEM replacement part, sold individually. This Bumper helps keep the fuel tank in place, and minimizes vibration of the fuel tank. This part is used with a variety of string trimmers, compatible with the models listed below.

This flanged star washer is a manufacturer-sourced replacement part designed for use trimmers. It is also known as a tooth lock washer due to its serrated inner edge which resembles inward facing teeth. These teeth bite into the head of the fastener and provide a better grip than standard washers. This washer also has a flange on one side...Read more which is a lip that extends past the edge of the washer. It helps to distribute the load of the fastener over a wider area to provide extra stability and a more secure hold. Over time the washer may wear down or become damaged. To remove the washer, first unthread the bolt/screw it is fastened on. Use pliers to grip the washer and gently twist it off. Place the new washer over the fastener with the teeth facing toward the surface being fastened and insert it into the designated hole. Ensure that it is locked into place. Each washer is sold individually.

Springs are used within outdoor power equipment to provide tension and shock absorption, depending on their application and use. This spring is designed for use within trimmers/brush cutters and is made to provide tension on the spool reel mechanism, and in some cases may be used to advance the line whenever portions of it are cut off. Th...Read moreis spring measures approximately 1.3-inches in length when extended and comes as an individual part. If you notice the line/spool in your trimmer is not advancing or is coming too quickly, the spring may be damaged and need replacing. Since this spring is a high-use part, it is not uncommon for it to lose tension over time and need to be replaced. To replace the spring, you will need to unscrew the covering cap, remove the spool feeding reel, remove the old spring and install the new spring with the rest of the assembly. Make sure to feed the line back into the appropriate feeding holes prior to operation of the trimmer.

This is an OEM replacement part. It has a left hand threaded screw to remove and attach it to the trimmer head. Its purpose is to hold the spool with the cutting line, in the spool housing. It also acts as the bumper to advance the line from the spool. This is a well used and abused part of the trimmer. It may be a good idea to order an extra one.

This is a Manufacturer Sourced replacement part for Lawn and Garden equipment. This item is Metal an is Sold Individually. A lock nut is a type of nut that resists loosening when properly threaded onto a bolt. This Locking Nut secures the cutting blade on the Trimmers/Brushcutters. You would need a Wrench to tighten or loosen this Hex Nut.

Genuine OEM replacement part, This item is sold as a kit. This is the complete Stringhead Assembly for the Trimmers shown below. It is a dual line head. To install this part, slide it on the spindle or shaft of the Trimmer The kit contains two Spool Retainers to secure the Stringhead. The red one has left hand threads and the black one ha...Read mores right hand threads. It will depend on the model you have, on which Spool Retainer to use. The cutting line diameter used in this Stringhead is .095

It is an authentic component that is supplied by the original equipment manufacturer for use with Homelite and Ryobi handheld string trimmers. This is an identical replacement for a missing or a faulty handle bar clamp that was installed on a new unit. The part is utilized to secure the handle bar. Please make sure to refer to the appropr...Read moreiate diagrams of your model for the correct location and application of this component. Keep in mind this high-quality clamp is made of durable metal and is sold individually.

This is a manufacturer approved replacement part designed for use with gas string trimmers. This tube is the fuel return line that returns fuel back into the fuel tank after the carburetor has been primed. It is made out of rubber and it is sold individually.

This starter pulley is an OEM part direct from Ryobi. This part is compatible with a variety of lawn and garden devices. The pulley is most often fitted between the air baffle and the container w/spring within the starter assembly. Please consult specific manual and diagrams for repair instructions. This part is sold individually. A screwdriver and a hex key are usually needed in making the replacement.