- Home
- HII8056U/03
- Instructions
HII8056U/03 Bosch Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Need to replace bake element
10 of 14 people
found this instruction helpful.
-
Ludovic from MIAMI BEACH, FL
- Difficult
- 30 - 60 mins
-
Nutdriver, Pliers
First, cut the power and remove the oven from the cabinet.
The bake element is accessible from the back and sits in a drawer.
As someone else said, you have to use pliers to bend the cover of the drawer, you will make some damage to the cover, but there is nothing you can do about it.
Make a note of what w ... Read more ire goes to the right and to the left so you can plug them back like it was before.
When you replace the bake element, make sure you insert it in the straps so it won't wiggle when it heats.
To close the cover that you bent, you will need a helper and push really hard.
The bake element is accessible from the back and sits in a drawer.
As someone else said, you have to use pliers to bend the cover of the drawer, you will make some damage to the cover, but there is nothing you can do about it.
Make a note of what w ... Read more ire goes to the right and to the left so you can plug them back like it was before.
When you replace the bake element, make sure you insert it in the straps so it won't wiggle when it heats.
To close the cover that you bent, you will need a helper and push really hard.
Read less
Was this helpful?
Thank you for voting!
Oven heating temp not turning off at set temp/overheating
9 of 18 people
found this instruction helpful.
-
Jaymie from Intercourse, PA
- Easy
- 30 - 60 mins
-
Screw drivers
Removed the wall oven to access temp probe connector strapped to the back of the oven. removed 2 screws holding probe inside the oven & replaced. Searched for the "fixing kit" thermostat part I was suggested to replace along with the probe. No thermostat type part was found in my oven, even though Bosch says it fits "somewhere". Reinstall
... Read more
ed the wall oven & tested. The temperature is working normal now. Will return the fixing kit.
Read less
Was this helpful?
Thank you for voting!
Control panel would randomly flicker, fade to black or become non-responsive when subjected to the heat/steam of the open range.
2 of 3 people
found this instruction helpful.
-
Alan from COLUMBUS, NJ
- Very Easy
- Less than 15 mins
-
Nutdriver, Pliers
Watch the YouTube video.
Turn off power or unplug the range.
Remove 5 gas control knobs.
Remove four T20 screws on Control panel. one on each end, L and R, two underneath, L and R.
Pull off control panel and carefully flip it up onto the range, being careful not to stretch the wiring harness.
Carefully remove two ... Read more wiring connectors (pinch and pull method)
Remove four T20 screws securing the Control panel mount then turn it over 180 degrees.
Straighten the mounting tabs until the control panel easily slides off of its mount.
Remove and replace the control panel and sheet.
Reverse the procedure to reinstall.
It took me longer to clean the components and the area that to repair the problem.
Tip: Isopropyl alcohol in a spray bottle and a cloth cuts the grease and grime, if needed, with very little effort and no scratching.
Turn off power or unplug the range.
Remove 5 gas control knobs.
Remove four T20 screws on Control panel. one on each end, L and R, two underneath, L and R.
Pull off control panel and carefully flip it up onto the range, being careful not to stretch the wiring harness.
Carefully remove two ... Read more wiring connectors (pinch and pull method)
Remove four T20 screws securing the Control panel mount then turn it over 180 degrees.
Straighten the mounting tabs until the control panel easily slides off of its mount.
Remove and replace the control panel and sheet.
Reverse the procedure to reinstall.
It took me longer to clean the components and the area that to repair the problem.
Tip: Isopropyl alcohol in a spray bottle and a cloth cuts the grease and grime, if needed, with very little effort and no scratching.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
broken glass/door won't stay closed
1 of 6 people
found this instruction helpful.
-
Michael from DES MOINES, WA
- Easy
- 30 - 60 mins
-
Screw drivers
installed new front glass panel.
installed thin magnetic catches on each side of door
installed thin magnetic catches on each side of door
Was this helpful?
Thank you for voting!