Models > HGI8054UC

HGI8054UC (01) Bosch Range - Overview

Sections of the HGI8054UC

[Viewing 10 of 10]
Keep searches simple, eg. "belt" or "pump".
ELECTRODE – Part Number: 00631633
ELECTRODE
★★★★★
★★★★★
(2)
PartSelect #: PS10057850
Manufacturer #: 00631633
$26.31
  In Stock
SHELF – Part Number: 00798845
SHELF
PartSelect #: PS9495699
Manufacturer #: 00798845
$48.38
  In Stock
Range Surface Burner Cap – Part Number: 00631626
Range Surface Burner Cap
PartSelect #: PS9495585
Manufacturer #: 00631626
This burner cap is for cooktops. Burner cap fits on top of the burner head. The burner cap protects the burner head from spills and helps spread out the burner flame for even heating.
$32.78
  In Stock
Cooktop  Burner Cap - Black – Part Number: 00631625
Cooktop Burner Cap - Black
PartSelect #: PS9495584
Manufacturer #: 00631625
This burner cap is for cooktops. Burner cap fits on top of the burner head. The burner cap protects the burner head from spills and helps spread out the burner flame for even heating.
$33.89
  In Stock
SLIDE – Part Number: 12024638
SLIDE
★★★★★
★★★★★
(1)
PartSelect #: PS12587595
Manufacturer #: 12024638
$75.03
  In Stock
Rubber Feet - Kit of 4 – Part Number: 00637940
Rubber Feet - Kit of 4
★★★★★
★★★★★
(1)
PartSelect #: PS11728745
Manufacturer #: 00637940
$48.38
  In Stock
KNOB-COOKING AREA – Part Number: 00632515
KNOB-COOKING AREA
★★★★★
★★★★★
(1)
PartSelect #: PS9495599
Manufacturer #: 00632515
$59.80
  In Stock
LAMP – Part Number: 00623710
LAMP
PartSelect #: PS8728930
Manufacturer #: 00623710
$5.38
  In Stock
Cooktop Burner Cap - Black – Part Number: 00631627
Cooktop Burner Cap - Black
PartSelect #: PS9495586
Manufacturer #: 00631627
Sold individually. This burner cap is for cooktops. Burner cap fits on top of the burner head. The burner cap protects the burner head from spills and helps spread out the burner flame for even heating.
$32.78
  In Stock
DISPLAY MODULE – Part Number: 12029207
DISPLAY MODULE
★★★★★
★★★★★
(1)
PartSelect #: PS12742171
Manufacturer #: 12029207
$266.10
  In Stock

Questions And Answers for HGI8054UC

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

Common Symptoms of the HGI8054UC

[Viewing 2 of 2]
Gas igniter glows, but will not light
Fixed by
these parts
Show All
Will Not Start
Fixed by
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Igniter replacement
Getting to the igniter is trivial, only requiring the removal of the stove bottom (two set screws) and a heat shield (the heat shield is held in place by screws with size 20 star-driver heads). At this point a splice could be made to the original wires, IF ceramic wire nuts were included with the replacement igniter (but, alas, they are not). IF a splice were made the repair would be a very easy, 10-minute job.

To replace the igniter then requires the complete removal of the back of the range (17, size 20 star-driver, screws, if I remember correctly), plus the removal of an additional heat shield (one more screw). Then one must carefully lift and free the back from tabs on both sides that are set into slots. (Oh, and you probably want to loosen the electrical cord shield that interferes with the back coming off.) The new igniter wire plug is only then very easily re-attached to existing harness. Everything is then replaced to finish the repair.

None of this is difficult, if you don't mind moving your range away from the wall and dealing with on the order of 20 screws. Personally, I think I would have rather found an igniter with ceramic wire nuts to splice to the original wires (certainly not as elegant as replacing igniter and wires entirely, but far quicker and easier).
Parts Used:
IGNITER
  • Jeffrey from Bloomington, MN
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
4 of 4 people found this instruction helpful.
broken glass/door won't stay closed
installed new front glass panel.
installed thin magnetic catches on each side of door
Parts Used:
DOOR-OUTER
  • Michael from DES MOINES, WA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Standoffs were not provided. The current standoffs needed to be remove and placed on the new board. (Not easy)
One the standoffs were removed they needed to be trimmed to attach to the new board. Took longer to do this than remove and replace board.
Parts Used:
CONTROL MODULE PROGRAMMED
  • Ruben from STAR, ID
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Socket set
1 person found this instruction helpful.