HES3053U8 Bosch Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Oven wouldn't operated. Error code F9
76 of 101 people
found this instruction helpful.
-
Richard from Centennial, CO
- Really Easy
- Less than 15 mins
-
Nutdriver
I called a repair place. They charged $54 to diagnose, (said it needed a new latch motor) then wanted $220 to complete the repair. I checked online prices and did it myself for about 15 minutes work and the latch motor itself ($44?).
Was necessary to uplug the range, pull it away from the wall and remove the back panel sheet m ... Read more etal, then 3 screws that mount the motor. Replace motor, reattach sheet metal. Plug in. Done. Ready to bake cookies.
Was necessary to uplug the range, pull it away from the wall and remove the back panel sheet m ... Read more etal, then 3 screws that mount the motor. Replace motor, reattach sheet metal. Plug in. Done. Ready to bake cookies.
Read less
Was this helpful?
Thank you for voting!
burned out burner
70 of 99 people
found this instruction helpful.
-
Lori from Winter Haven, FL
- Easy
- Less than 15 mins
-
Pliers, Screw drivers
First we removed two screws under the rim of the range top to open the lid. Lifted the lid and removed the screws from the bracket that holds the elements, Be careful with the clips that hold the element in, if you break them or bend them there aren't any more! Also note which holes they were in, they are marked according to the differ
... Read more
ent sizes of elements. Disconnected the wires, needed needlenose pliers to grip them...connected new element, popped it back in place, replaced bracket, closed top ...Easy peasy!!!
Read less
Was this helpful?
Thank you for voting!
Burned element
65 of 120 people
found this instruction helpful.
-
Tom from Wallingford, CT
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
Flip up top, remove wires and two screws. Replace in opposite way. Turn off power to stove first.
Was this helpful?
Thank you for voting!
anti-tip bracket not installed
35 of 47 people
found this instruction helpful.
-
Brian from Panama City Beach, FL
- Really Easy
- Less than 15 mins
I was selling my home and did not realize that the anti-tip bracket was not originally installed. A home inspection caught the problem and the buyers required that I install one. I could not find the original and obviously the installer never put it in place to begin with. The buyers wanted this resolved within a week so I had to act f
... Read more
ast. I could not find one locally so I found what I needed on your website. It arrived in a couple of days and was easy to install. I used the template provided in the kit and drove the screws through the bracket into the wood plate behind the drywall. Pushed the range back in place and that's it. Couldn't get any easier.
Read less
Was this helpful?
Thank you for voting!
Needed an extra rack to bake more bread
19 of 31 people
found this instruction helpful.
-
Albert from Havertown, PA
- Easy
- Less than 15 mins
I opened the door of the gas range and slid the rack in. No one can do this! I am amazing.
Was this helpful?
Thank you for voting!
Aluminum foil accidentally put on bottom panel ....burnt up, left non removable residue.
10 of 11 people
found this instruction helpful.
-
lewis from COLDWATER, MI
- Easy
- 15 - 30 mins
-
Screw drivers
After 15 minutes of frustration and back breaking I removed the oven door and had much better access to the panel, from there on it was all down hill.
Was this helpful?
Thank you for voting!
Old element connections different from new element
11 of 14 people
found this instruction helpful.
-
Frederic from KILLEEN, TX
- A Bit Difficult
- 30 - 60 mins
-
Pliers, Screw drivers, Socket set
Disconnected power at breaker. Removed cooktop mounting screws, lifted top and propped in up position. Removed two screws and lowered two front burners mounting frame. Wiggled dual element free at the clips and proceeded to swap wires one at a time and realized the difference with connectors 1a and 2b much later when only the center porti
... Read more
on was heating up. Finally figured out the problem and everything works as advertised. Pay attention if you own a Kenmore product.
Read less
Was this helpful?
Thank you for voting!
Element Burn out
25 of 60 people
found this instruction helpful.
-
Jesse from Forest, VA
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
Self easy
PS Great service Super FAST.
Thanks Jesse
PS Great service Super FAST.
Thanks Jesse
Was this helpful?
Thank you for voting!
One section of heating element failed to heat.
7 of 7 people
found this instruction helpful.
-
Fred from VESTAL, NY
- A Bit Difficult
- 1- 2 hours
-
Pliers, Screw drivers
Followed on-line instructions to remove the defective heating element. Some connection tabs on the replacement unit were different than the original. One tab was too wide to accept the stove's slip-on wire connector without fling down the tab width on the heating element. Thanks to some on-line instructions, wire connections to element 1a
... Read more
and 2a had to be reversed. If not for those instructions I would probably have ended up sending the unit back to the supplier, as an incorrect replacement !
Read less
Was this helpful?
Thank you for voting!
Oven light bulb went dark; it needed replacing
10 of 17 people
found this instruction helpful.
-
Lise from CEDAR GROVE, NJ
- Very Easy
- Less than 15 mins
Twisted replacement bulb into place easily. Let there be light!
Was this helpful?
Thank you for voting!
2 elements stopped working.
9 of 14 people
found this instruction helpful.
-
Ruth from MORGANTOWN, WV
- Really Easy
- 30 - 60 mins
-
Nutdriver
My husband followed the video instructions and it was easy to fix.
Was this helpful?
Thank you for voting!
Aluminum foil baked on surface
6 of 6 people
found this instruction helpful.
-
Cindy from RHINELANDER, WI
- Easy
- Less than 15 mins
-
Screw drivers
Took out 2 screws, removed panel.
When you put the panel in don’t push it tight to the front or the screws won’t align. Just place in gently and the screws will align
When you put the panel in don’t push it tight to the front or the screws won’t align. Just place in gently and the screws will align
Was this helpful?
Thank you for voting!
broken lens over oven light
11 of 22 people
found this instruction helpful.
-
Leslie from Warsaw, VA
- Really Easy
- Less than 15 mins
Your service was OUTSTANDING...Ordered one afternoon, and before lunch time the next day, the delivery man rang my door bell...Thanks a bunch for you excellent service.....
Was this helpful?
Thank you for voting!
old element coil burned apart breaking the circuit.
6 of 8 people
found this instruction helpful.
-
James from WARRENTON, MO
- A Bit Difficult
- 15 - 30 mins
-
Nutdriver, Screw drivers
removed the old burner and put the new one in it's place.
Was this helpful?
Thank you for voting!
Bottom panel burned through
5 of 6 people
found this instruction helpful.
-
Barry from MENDON, NY
- Really Easy
- Less than 15 mins
-
Screw drivers
Remove two back knurled screws, lift out old bottom, screw in new bottom panel. Removal of oven door (two flip out handles at hinge( makes this a little easier. Our oven did not need any other dis-assembly.
Was this helpful?
Thank you for voting!