HDA2000Z01AD Hotpoint Dishwasher - Instructions

Turned off breaker. Turned off water and disconnected water line to make it easy to pull unit out and turn on it's side. Once that was done it was an easy swap out. Exact same motor/pump assembly. Love this site. Thanks

Unplugged the machine then removed the two connectors to the motor. Loosenned the hose clamps, pulled the hoses took off the balancing bar,removed old motor assembly and put new one in. Reverse all the steps plugged the machine back on and was done in less then twenty minutes.

pulled washer out and turned it upside down to get to the pump&motor.
no problem to fix

followed instructions that came with the part. My dishwasher had a slightly different configuration than what the directions said so disassembly took a few minutes to figure out. Once that was done, the removal of the old impeller assembly and installation of the new went quite smoothly. The replacement assembly had a "grater" which wa ... Read more s not present on my original however it installed perfectly and no longer leaks.

Piece of cake. All done and working just fine.

Originally replaced solenoid without pulling unit out, but continued to leak. Purchased the entire motor and pump kit; pulled unit out, turned it on end and replaced the motor. The only problem was that no new ground screw was sent with the kit and the existing screw wasn't quite short enough to connect. Either the hole on the replacem ... Read more ent kit needs to be deeper or a bond screw needs to be sent that will fit the new kit. We had to find our own screw that would fit properly.

Most time spent was removing washer out from beneath the counter. Motor and pump installation was a breeze. Everything I needed was in the kit and easy to follow the instructions provided. Saved a lot of money and washer runs perfect. Thank you.

Removed the dishwasher from under the counter, found where the leak was coming from, which took the most time. We ordered the new part on line, it came the next day and the installation of the new part took about 30 minutes and the dishwasher is like new now. This procedure saved us a lot of money.

I disconnected the water line on the left-front. Disconnected the drain line at the air-break. I removed the AC power-in box on the right front and disconnected the power lines going to the unit. I took out the two screws holding the unit to the cabinet (above the door) and slid the unit out onto a drop cloth (protect the floor; some wate ... Read more r spills). Pulled the unit out and turned over. Followed the directions with the motor & pump valve kit, which were very easy to follow. Then reversed the above. Nut drivers are a must for this job.

replaced the master toner relay.

I had some extra problems with my water supply line since this is an old house, but I won't dwell on that. If you have an older model like mine (probably 80's) the only trick is with the drain solenoid. The kit uses a newer style solenoid that is a little different. Without getting too technical here, let me just say that if the old solen ... Read more oid has a little metal lever that is actuated when the plunger goes down do not discard it. From what I have read, the dishwasher will shut down with an error code if you don't use this part and you will also have 2 wires that are just hanging there with nothing to plug in to. You will need to use an included metal plate and screws to adapt that part to the new assembly. It takes a little mechanical aptitude, but after you figure it out it works perfectly. I did not see this mentioned in the instructions but the necessary parts were included. Replacing the pump and motor was fairly simple, and all the needed parts were included in the kit. I did remove the unit from under the counter and lay it on it's back for easy access to the pump and motor. It helps to watch some You-tube videos if you are unsure about how to do this, but make sure they are working on the brand you have. All dishwashers are NOT the same.

I had to readjust the door latch to get the door to close

Removed the existing inner door by removing screws along the edge of the inside door. Had trouble removing the door latch but after lifting it on one side of the plastic door fitting, it eventually lifted out. I also had some trouble getting the spring loaded soap door back into the replacement inner door. After playing with it for awhile ... Read more I realized that the soap door should be in the open position when putting the spring latch back on. The soap door won't close until you get the entire inner door mounted and back on. I also want to note the the inside vent in the upper part of the inner door needs to be removed from the old inner door and installed in the new one. I missed that at first and it allowed condensation to get inside the door which caused the dishwashers alarm to go off during the dry cycle. One last note that I initially decided not to replace the existing sound proofing material in the new door based on advice from a website that stated that I wouldn't notice the sound difference. That was definitely untrue. I had to disassemble the door, replace the sound proofing and then it sounded fine. Overall it was a little difficult to figure out but considering how inexpensive the replacement door was compared with a having a service repairman come out, it was worth the trouble.

Turn off the power at the breaker panel. Turn off the water supply that goes to the dishwasher. Remove the front lower panel to gain access to disconnect the water line and electric. Now remove the two screws that connect the dishwasher to the countertop. You should be free to slide the dishwasher from under the countertop far enough to r ... Read more emove the drain hose. Slide the dishwasher out all the way and lay on the floor door down. Loosen the two clamps that hold the motor up. Remove the motor bracket, (should only be one screw. Disconnect the wires from the motor. Now just pull the motor down and out. Repeat the process to install the new motor. I took several pictures before I started removing anything. The instruction that comes with the kit is very good. Their will be parts in the kit that will not be used. Not to worry!

This was a 45 min project. New pump was a redesign. Match your style with the instruction sheet. ( pictures are upside down) Install drain on pump. Remove wirng connectors(3) and hanger. Raemove in/out pump clamps, and remove pump. Reverse procedure( I had to bend the new hanger to fit). When I first fired it up, nothing happened for abou ... Read more t 5 min. Then water got into the pump and it started working. Quieter, more powerful spray. Grabbed a beer.