HDA2000F04BB Hotpoint Dishwasher - Instructions

Checked the water supply to the inlet valve - OK, pulled the filler hose from the outlet side of the valve and checked flow in wash cycle. Results, less than 1/2 gallon. Checked your website, found 94% sucess rate by replacing the valve, so I ordered one. It took about 10 minutes to install with a nut driver, 6" adjustable to connect w ... Read more ater supply, and plier to hold outlet clamp open to install it; now we look forward to dirty dishes rather than dumping water into the machine it takes care of itself and we once again get sparkly cups andglasses of the top rack. OU- Rah!!

I removed the old cap and put on the new cap.

I removed the broken stub of the old fill cap with a screw remover. This was the only part that wasn't easy. The new cap fit fine.

Unscrew old stripped out one and put in new one ..wala!! Easy repair for this old lady...

Researched problems on internet,based on info ordered part. Got it in 24 hrs.followed package directions. So easy and for less than a service call! Runs like a charm now.

Removed dish washer from cabinet area and snapped new clip into cable and hook into support.. The time that took the longest was to removed the screws to pull the unit out of the cabinet area.. Very easy fix...

Replaced the water-fill solenoid valve.

Removed existing gasket seal on door. Cleaned really well with a household cleaner around the gasket crease. Installed new gasket seal around door. Started with small notch in the middle of the gasket to center on top and then slowly fastened into door edge and slowly snug around bottom edge where the deal is notched and the the diffic ... Read more ult part was to feel the seam again on the bottom to re attach seal after notch from corner. Rupert this on the other side of door.

after watching related video on partselect.com, diagnosis and repair couldn't have been much simpler!

Held panel in place and drilled holes and installed drill screws.

Laid on floor remove two small bolts with nutdriver,loose water line with wrench,remove other water line with pliers.Remove water inlet valve and replace with new one

Wow, could not have been easier. The suggested repair stated that the water inlet valve was the problem 93% of the time. And, it was spot on. It was the exact same replacement part. And, once installed, it worked like a charm. I have bookmarked this website, and will use it for all future appliance repair. I simply could not be more ... Read more pleased. It was a breeze. Thanks,

Remove front shields on bottom of dishwasher. Shut off dishwasher and electricity. Unplug electric connection. Unscrew brace holder screws on front. Remove clamped on hose at back of valve. Unscrew valve from copper water pipe. Screw on new valve to copper water pipe. Put on clamped hose. Screw on bracket. Plug in electric connection.

i first order the corner baffles and put them in. no change at all, still leaked terribly. the old baffles looked pretty good so i kept them. i then ordered the door gasket and the insert. i removed the old one, put in the new, and still no change. i thought perhaps the machine hadn't been used at all because it was like brand new inside ... Read more , and previously owned by 'a little old lady'. i decided to load it up and run it on a regular wash, and have done that three times now. it drips a very small amount on the left corner but i'm quite happy that it decreased so much. I think perhaps the seal might be setting with the heat of the cycle because each time a load goes through it get less and less drips from that corner. The first order was sent by ups and they couldn't find where i lived so i actually had to go pick them up, but the second order was sent fedex and they had no problem finding my home, and i was very pleased with how fast my order came.

first off if you can understand the problem DO NOT CALL THE GE REPAIR SERVICE AND HAVE A REPAIRMAN COME TO YOUR HOME you will save over $300.00. a mistake i made, it cost me $79.95 just for him to tell me the dishwasher was broken and then i was told it would cost me over $300.00 to fix it. WHEN I TALKED TO PARTSELECT I FOUND THE WATERVAL ... Read more VE FOR A LITTLE OVER $55.00 WITH SHIPPING IT TOOK ABOUT 20 MINUTES TO DISCONNECT THE DISHWASHER AND REMOVE THE OLD PART AND ABOUT THE SAME AMOUNT OF TIME TO REPLACE THE NEW ONE THEY EVEN HAD GOOD INSTRUCTIONS IF YOU NEEDED THEM. I FOUND PARTSELECT SERVICE TO BE A VERY GOOD BUSINESS TO WORK WITH. ROY F BURTNETT