HDA1000G02WH Hotpoint Dishwasher - Instructions

There are eight guides that hold the rack rails in place. Use a Phillips screwdriver to remove the top two guides on each side in order to remove the rack from the dishwasher. The plastic axles on the rack and the rollers snap on. Use the hammer and punch to bend the metal clip on one end of the rail. Remove the plastic end piece then slide the rollers out. Place two new rollers in the rail and put the plastic end piece on. Use the hammer and punch to bend the metal clip back into place. Snap the rails on the rack and set the rack on the guides in the dishwasher. Replace the top guide using the screwdriver, you will have to twist the rails in order get them in between the
guides.

Unsnapped clip,and moved it 90 degrees. Slip wheel and clip off. Installed clip on new wheel. replaced new wheel. The wheel did not come with a new clip and was not suggested on the parts list. The existing clip was still OK but if it was not, I would have had to order a clip and wait. All in all, a good experience.

Open the tiny plastic package in inserted the wheel onto the "axle". Opened the dishwasher, pulled out the bottom rack and snapped the wheel onto the rack. Done!

The wheels came with a clip on part that clipped to the rack and the wheel snapped into that clip. I am a woman and it was easy for me to do. Thanks to Parts Select for being an easy to use and navigate site, for quick shipment and for good directions with the parts. Sincerely, Teresa from Alabama.

Used the pliers to remove the broken roller. It came off in pieces. Slid new one on.

Cap on end of roller track was a bit of a challenge. It sort of twists & pulls off.

First removed four old wheels. then attached four new wheels to lower rack by pressing into slots.

Just pulled off the old wheel. I just had to push in the stud to the wheel and pushed it on to the rack of the dishwasher. Very easy repair! Only disappointing part was that it bothered me to have to purchase the stud with the wheel. I was told they only came as the set. I only needed to purchase that inside stud. My wheels were fine.

1. I removed the plastic stops from the ends of the upper rack slides.
2. Removed the upper rack.
3. Unclipped the old rollers from the rack.
4. Clipped the new rollers onto the rack.
5. Made a grunting noise so the wife could hear.
6. Walked away

Remove the front coverfrom the machine. This is done by removing the 3 screws at the bottom of the panel. The panel then drops down and pulls straight off. The pump is located on the front right wall of the of the machine. You will notice a 2-3 inch diamete threaded cap on the right side of the front wall of the machine. This is the front of the pump and access to the filter. Place a large bucket under this cap and slowly loosen the cap. All of the water remaining in the machine will begin to drain (this could be a lot of water. Do not remove the cap completely so that you can quickly stop the flow of water if needed). Once all water is drained from the appliance, Disconnect the two hoses from the pump using a pair of pliers to looses the presure clamps, sliding the clamps back an then pulling off the hoses (be careful of any remaining water in the hoses). Then remove the two screws from the rear base of the pump that secure it to the bottom floor panel of the washer. Slide the pump slightly to the rear to free it from the fittings on the front wall of the machine and the lift the pump up. At this point, firmly pull out the wiring harness plugged into the top right side of the pump. Install the new pump by plugging in the wiring harness and resecuring the pump. Plug in the machine and run on the rinse and spin cycle to test.

Pulled the end cap off and replaced the wheel.
most of the parts were for future repairs

First and formost before you buy read everything in trouble shooting your dishwasher. Then you do not buy parts you do not need. First you turn off power, then water. Remove two screws, a rubber hose and a hard line by unscrewing if you are lucky some contractors might sweat this on. No biggie just two extra steps that's all. do in reverse to assemble...

replaced rack, no repairs required

popped old wheel off popped new one on
for the rack roller i took the ends off and slid old rollers off then slid new ones on.

lower rack took one min. take out old slide in new

upper rack a little tricky had to remove end caps on rack arms to slide rack out to replace rollers. end caps are not snapped in they have a lever in the track that is part of the cap if you twist it a little cap will slide off.
total time for this part 15 min.

I took the two drain hoses off with the pliers then only two screws that holds the pump. After that the two hot wires which are black and white. But remember to unplug you're washer since the pump is not grounded you don't want to risk being shocked. Hope thi helps. Plus i saved around 250.00 by repairing myself.