My Orders
- Home
- HBL57M52UCC/02
- Instructions
HBL57M52UCC/02 Bosch Wall Oven - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Need to replace bake element
8 of 12 people
found this instruction helpful.
-
Ludovic from MIAMI BEACH, FL
- Difficult
- 30 - 60 mins
-
Nutdriver, Pliers
First, cut the power and remove the oven from the cabinet.
The bake element is accessible from the back and sits in a drawer.
As someone else said, you have to use pliers to bend the cover of the drawer, you will make some damage to the cover, but there is nothing you can do about it.
Make a note of what w ... Read more ire goes to the right and to the left so you can plug them back like it was before.
When you replace the bake element, make sure you insert it in the straps so it won't wiggle when it heats.
To close the cover that you bent, you will need a helper and push really hard.
The bake element is accessible from the back and sits in a drawer.
As someone else said, you have to use pliers to bend the cover of the drawer, you will make some damage to the cover, but there is nothing you can do about it.
Make a note of what w ... Read more ire goes to the right and to the left so you can plug them back like it was before.
When you replace the bake element, make sure you insert it in the straps so it won't wiggle when it heats.
To close the cover that you bent, you will need a helper and push really hard.
Read less
Was this helpful?
Thank you for voting!
Oven was not heating properly
3 of 5 people
found this instruction helpful.
-
Barry from MONROE, NY
- Really Easy
- 15 - 30 mins
-
Nutdriver
Took the one out of the box and take off the back plate and detach the sensor
Was this helpful?
Thank you for voting!
Temperature settings stenciled on the Facia were damaged.
1 person
found this instruction helpful.
-
Ed from FREDERICKSBRG, TX
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers
Replace facia panel. Turn off power to the oven. Remove oven control knobs by inserting finger tips under each side of the knob and pulling. Open oven, remove mounting screws. slide the oven out a few inches to allow clearance for the removal of the facia panel. Remove 3 torx screws under the bottom of the facia panel. The wiring harness
... Read more
es for the LED temperature display and touchscreen are very short and must be disconnected in order to remove the facia. Slowly pull out the bottom of the facia panel taking care not to damage the wiring harnesses. Locate the wiring harness connections and disconnect. Lift the facia panel up and away from the oven. Carefully remove the LED temperature display from the back of the facia panel touch screen. Installing the new facia panel: The LED temp display wiring harness is very short and difficult to connect with the LED display installed on the new facia touchscreen panel. For this reason connect the wiring harness to the LED temp display before installing it in the new facia. Once the wiring harness is connected to the LED display, place the facia panel in position and reach under, align the LED display with the touch screen panel mounts and snap into place. Connect the touchscreen harness, position the facia panel and replace the three screws. Secure the oven in place, replace the knobs, and turn on the power.
Read less
Was this helpful?
Thank you for voting!
broken glass/door won't stay closed
1 of 6 people
found this instruction helpful.
-
Michael from DES MOINES, WA
- Easy
- 30 - 60 mins
-
Screw drivers
installed new front glass panel.
installed thin magnetic catches on each side of door
installed thin magnetic catches on each side of door
Was this helpful?
Thank you for voting!