GWS645RBS4 Gibson Washer - Instructions

unplugged machine. pried up with large regular screwdiver on top washer lid. removed two phillips screws bottom of front panel, had to use rubber mallet to drive front panel down to remove as was rusty and old. removed old belt using screwdriver. put new belt under tub pulley and put belt on small pulleys. kept moving tub and springs ... Read more by pushing on tub. Took several tries to get new belt to go on the large tub pulley but finally did it. I used the instructions you gave for replacing broken drive belt and it worked. replaced front panel and two phillips screws, put top back on and away it went.

Purchased both the belt and idler pulley. Bought the idler pulley "to have it if it were needed" since it was only a $15 part.

Watched two videos provided on PartSelect for our model number with our symptoms. Both showed an easy access of idler pulley at the front of the washer. My emailed invoice also contained links to the ... Read more video for each part.

Getting the panels off went exactly like the video. However, the idler pulley was nearly on the back side of the tub assembly/transmission and NOT easily accessed as shown in the video.

I replaced the belt and ran the washer without replacing the idler pulley. Since it performed very well agitated/spun I elected to avoid the daunting looking task of idler pulley replacement. Hung it up for "just in case" future use....again not hard to do at only $15.

ordered the new pump,its a lot more heavy duty than the orginal.had to change the mounting bracket somewhat. the new pump mounted bythe bottom of the pump housing and theold pump mounted by the side of the pump housing. so, wnere the curve was in the mount, I used the bench grinder to cut the curve out to make a flat surface for the new p ... Read more ump to rest in ,also drilled two 1/4 inch holes in the mount for the bolts to mount the pump.

After struggeling the most with lifting out the inner drum and then the wash drum. I realized when the job was complete a better way. 1. Take the top off the washer. 2. take the front off the washer. Then disconnect all wires and hoses from assembly One small hose on the tub and the pump hose at the bottom. 3. at the bottom of the overall ... Read more assembly there are 3 braces holding the tub assembly with 2 springs on each brace. Go under and remove the springs and then lift the whole assembly out into the middle of the floor. 4. remove the top cap off of the agitator. 5. remove the agitator. 6. if you are lucky and the bolts are not seized in the block that holds the shaft remove the small steel block from the bell and remove the bell. 6. Slide the inner tub up and off the shaft and again if all goes well the outer wash tub should slip up off the shaft as well. 7. remove the drive belt from the motor and transmission.

Disconnected power, removed hoses, removed housing and pump. Re oriented drain pipes on pump to align with washer hoses (just twist collar and re set) attach foot bracket and secure to washer bottom. Attaching the hoses with the compression clamps was a bit of a problem until I used pliers to press the ends together and then an adjustab ... Read more le wrench to hold them tight. Slid on hoses and released clamps. Replaced electrical and secured pump cover. Done in about 15 minutes.

Loosened top of washer from spring tabs and leaned it against wall, removed two phillip head screws from the front bottom panel, removed panel. Removed spring clamps from 2 hoses( make sure water is drained from tub before doing this!!) on pump, removed 2 wire connectors. Used nutdriver to remove 2 screws that held down pump. Replaced pum ... Read more p and everything else installs in reverse. Almost forgot, the plate that holds the pump to the bottom of the washing machine has to be removed from the old pump and attached to the new one.

remove one hose clamp.pulled hose from back of washer.replaced with new hose in same procedure.best of all i had my new hose in two days.great serviceand inventory.

Tilted the clothes washer back to provide easy access. Then after scrubbing the floor - which took most of the time of the repair, screwed out the broken leg and screwed in the new leg or SCREW. Easy peasey.

Disconnect power,take water hoses off using pliers,they are really tight,remove 2 philips head screws,pull 2 wire connectors off and water fill hose squeezing wire clamp and sliding clamp back on hose.reverse to install.Works like a champ.

We have a washer/dryer stack type. For a week or so, my wife mentioned that washer is louder than normally is, shortly, the washer stopped spinning and the clothes were finishing soaking wet.

I opened the front panel sheet and saw the broken belt, ordered the belt online. The belt arrived in 2 days, and the actual belt-replacem ... Read more ent took 10 minutes. The washer functional like new.

Very easy
Unhook electricity
Took bottom front cover off
Took plastic motor cover off
Unhooked electrical connections
Moved clams on hoses and took hoses off
Took bolts out that held in pump
Took bottom bracket off of old pump and put it on new pump
Turned the adjustable hose connection to the right ... Read more same posstion as old pump
Bolted new pump on
Connected the water hoses
Connected the electrical connections
Bolted plastic motor guard back on
Bolted on front bottom cover
Plugged in and Wallaa!!!
I run one load before installing front cover, to watch for leaks
And the video sent with email was very helpful
Thanks
And have a good day!

Poped up top, removed front pannel (2 phillip head screws) observed failed belt. Replaced belt. Tensioner can be held back by hand so it was easy. Works great. Part Select Rocks! I put in the model number and bam, there was my needed part, 3 days later it was in my hands. This was after me wasting time driving around town trying to ... Read more find it at home depot type stores to no avail. I'll never do that again. This website makes repairing appliances a snap. Gotta love on-line shopping! woo hoo

I looked up the repair on You Tube and it looked easy! Take off the top of the machine (unplug and disconnect water first), 2 wire connections and 2 screws to mount. The only problem I had was screwing the mounting plate on the machine. It needed some help enlarging the hole a tad, I used an awl. Reconnect the water and plug in.This Grann ... Read more y rocks!

we took the hoses off then unscrewed the bracket that was connected to the part and then once out we put bracket onto the new part and screwed it back to the washer connected the hose back and WOW the water was flowing

Removed old pump and installed new pump in same order. Only problem was reinstalling wire spring clamps with hoses on new pump. Not enough room to use pliers to open clamp. Otherwise a simple installation. A small vise grip pliers might help to hold clamp open. Check and rotate inlet/outlet end of pump as included directions describe firs ... Read more t before installation.