GWS1339CS1 Gibson Washer - Parts

This rubber V-style drive belt slips on the motor pulley to bring the basket to the required speed. If you notice a burning rubber smell or grinding noises coming from your washer, your washer does not start, drain, spin properly (will not spin/spins slowly/will not agitate properly), or if your washer shakes or moves during the cycle; ch...Read moreeck your drive belt for signs of wear and tear. Replace the drive belt if you notice that the belt looks damaged. This OEM part is approximately 35 inches in length, and sold individually.

This is a 120 volt, 60 hertz drain pump that is manufactured to remove water from the tub of your washer once your clothes are washed. This part is the pump and motor assembly, which includes a red flapper to prevent drain backflow. You will need to remove the front panel of your washer to access the drain pump. The tools you will need fo...Read morer the repair are a Phillips screw driver, a putty knife, a pair of slip joint pliers, and a 5/16 nut driver. Be sure to disconnect the water supply from your washer before doing the repair. The metal edges on the appliance are sharp, so use work gloves to safely complete the repair.

This is a screw in leveling leg for your washing machine. It supports the appliance by screwing in place to create a stable and flat surface. Take note that you are able to adjust the height of your appliance to make it leveled. This model is made entirely of plastic and is white in color. It is just under 2.5 inches long, 1.5 inches wide, and the head has a diameter of roughly 1.5 inches.

If you have a leaky washer, then your tub seal may be the culprit. The tub seal assembly may also be known as the washer tub seal, and is a part for your washer. The function of this piece is to make sure water does not lead from between the outer tub and the spin basket from around your basket drive shaft within your washer. To replace y...Read moreour old part with this one you will need a flathead screwdriver, Phillips head screwdriver, pliers, putty knife, 7/16 socket, spanner wrench, and a hammer.

The idler pulley on your washing machine allows the drive belt to operate smoothly. If your washer is not spinning or agitating, makes too much noise, or you notice a burning smell when it is operating, you might need to replace the tension idler pulley. The tension idler pulley works in conjunction with the drive belt, so you might need ...Read moreto replace the belt as well as the pulley. Once the old pulley has been removed from the washer, you will need to transfer the spring and bushing from the old pulley to the new one before re-attaching it to the washer.

This is a replacement screw for your washer or dryer. The screw is approximately half an inch in length and is a Phillips-head screw. It screws in from the outside of the drum, into the vane/baffle. The main reason you would replace this screw is if the old screw is missing or damaged. This part is sold individually and is an OEM part sourced directly from the manufacturer.

Sold individually.

Mounting bracket on this part replaces old style ( You may need to drill off old bracket before mounting new lock).

This dual action agitator assembly is a key component in top-load washing machines, designed to deliver powerful, back-and-forth motion that agitates laundry during the wash cycle. By promoting thorough movement of clothes through water and detergent, it enhances cleaning performance and helps remove dirt and stains effectively. Its dual-...Read moreaction design also minimizes tangling, ensuring even distribution and gentle handling of fabrics. Constructed for durability and compatibility with select washer models, this genuine replacement part restores original functionality and supports efficient, reliable operation. It is ideal for resolving issues related to poor cleaning results or excessive fabric twisting.

This drain hose, used in washing machines, delivers water from the drain pump to the house drain. The hose is 7 1/2 feet (90 inches) long. If your hose is leaking, it is best to replace it with a new one. To repair it, first access the back of the washer and remove the clamp holding the hose. Switch the clamp onto the new hose before plac...Read moreing it back into the fitting. Refer to the manual provided by the manufacturer for further instructions and guidance. Remember to unplug the appliance from the power source before beginning installation.

The agitator drive block rotates the agitator assembly in your washer. If the drive block breaks down due to wear and tear the agitator will stop working. If you notice that your washer is making loud noises while washing, this may indicate an issue with the agitator block. You will find this part underneath the dispenser cover and cup. Y...Read moreou will need a 1/2-inch socket to remove the agitator bolt and then simply lift off the agitator (this may require some effort to lift off). Use a flat-head screwdriver to remove the old drive block, push the new one into place with firmness. This part is made of metal and measures about 2 inches long and 1 inch wide.

The spin bearing, used for your washer, is located at the bottom of the outer tub near the transmission. The spin bearing carries the transmission shaft in the drive system, therefore ensuring the shaft is spun properly during its spin cycle. If your spin cycle makes loud or odd noises, replacing the bearing could be a solution to your pr...Read moreoblem. Refer to the diagram provided by the manufacturer for further installation instructions. As a safety precaution make sure to unplug appliance from the power source.