This lid lock, also known as a door lock, is a genuine OEM replacement part for your washing machine. The lid lock keeps your washer lid closed during the washing cycle. If this part is broken, your w...
This drain pump assembly is for washers. Drain pump assembly removes water from the washer during the drain portion of the cycle. The assembly may include multiple parts; refer to your parts diagram f...
This rod and spring assembly is designed to fit with washing machines and is made by the original manufacturer of your washer. It is a part of the washer suspension system that helps to stabilize and ...
This is a manufacturer-made suspension rod and spring assembly for your washing machine. This suspension rod is one of four suspension rods that make up the entirety of the inner suspension of your wa...
This drive belt is sourced from the original manufacturer for use in various models of dryers. It is a rubber belt that connects the motor to the transmission of the washer. It enables the drum to spi...
This is a clutch for your washing machine. The clutch is made of a white plastic material and is used within washing machines to engage and disengage the transmission during the wash and spin cycles, ...
This is a mode shifter or shift actuator for models of washing machine. Mode shifters are designed to change the function of the washing machine motor, between spinning cycles and agitation, and is us...
This is an inlet valve for models of compatible washing machines. Inlet valves are electrically controlled solenoid valves that open and close as needed during the washing cycle, to allow water into t...
This is a speed sensor for a variety of washing machine models. Speed sensors are used to monitor the speed of the washer drum and communicate it to the electronic control board to slow or quicken it....
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
18 questions answered by our experts.
Sort by:
< Prev
1
2
3
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Ray
December 9, 2019
How do i get to the recirculation tube
For model number GTW680BSJ5WS
Hello Ray,
Thank you for your question. You will need to remove the tub assembly to have easy access to the tube, first pull the washer away from the wall and locate the two screws at the back of the washer -- one on each side -- that secure the control console to the top of the machine. With a Phillips screwdriver, remove the screws. From the back of the washer, grasp the console on both sides and move it forward one-half inch. After that you will be able to see the re circulation pump and the tube with it. Hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Jim
December 11, 2023
Do you have to replace the water valve seals if you replace water valve assembly?
For model number GTW680BSJ5WS
Hello Jim, thank you for reaching out. We have researched and found that the water valve seals comes with the water inlet valve assembly. You may need to remove the old seals to install the new water inlet valve assembly. Glad to be of help!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Jeffrey
November 30, 2019
How do i get the backoff
, the machine is making a squealing noise
For model number GTW680BSJ5WS
Hello Jeffrey and thanks for writing.
Pull the washer away from the wall and locate the two screws at the back of the washer -- one on each side -- that secure the control console to the top of the machine. With a Phillips screwdriver, remove the screws. From the back of the washer, grasp the console on both sides and move it forward one-half inch. We hope this helps. Please contact us anytime.
Was this helpful?
Thank you for voting!
Edward
February 1, 2020
Softern not emptying
For model number GTW680BSJ5WS
Hello and thank you for writing.
It certainly sounds like it could be a damaged dispenser PS12171718 you should check the part(s) for signs of damage and replace the part(s) as needed. We hope this helps. Please contact us anytime if you require further assistance.
Drain all the water out of the tub with a shop vac Remove rear drain hose and drained rest of water into a bucket Remove small rear panel (bottom left hand corner) where the drain hose connects Tipped washer up about 45 degrees to get underneath it - Supported it with a few paint cans Remove internal drain hose/clamps
... Read morefrom pump - w/ pliers Remove belt cover (gray plastic) with socket - 3 bolts Remove wire assembly plug from socket Remove old drain pump with socket - 3 bolts Install new drain pump - 3 bolts - plug wire assembly into socket Reinstall belt cover - 3 bolts Reinstall hose to drain pump (note panel will be inside washer) Feed drain hose panel through hole and reinstall - 1 nut Re attached drain hose to exterior drain plug You are done !
Very simple to repair. Be sure to drain the tub outside or into the sump pump then lay the washer on its side. The pump is right there on the bottom of the basket with 3 bolts. You will also need to remove the belt cover to get to the plug. So simple and saves you hundreds off repair man prices.
Use putty knife to unlock top panel from base. Remove 2 bolts from back of washer holding control section. Don't take completely off. 2 bolts needs to be removed to unsecure top from base. Lastly 2 screws hold lid in place. Remove lid. Slide top panel to left just to access lid lock. Unplug sensor. 1 screw and tabs hold lock in place. Wat
... Read morech position coming out so you don't get confused putting new lock in. Squeeze tabs, replace screw. plug in sensor. Reverse procedure to put top section back together.
