EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

GSH25JGDDBB General Electric Refrigerator - Overview

Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Refrigerator Ice and Water Filter – Part Number: MWFP
$74.23
In Stock
Refrigerator Ice and Water Filter
★★★★★
★★★★★
(82)
Part #MWFP
This ice and water filter helps reduce impurities in select side by side and bottom freezer refrigerators. Replace it about every six months, or when water flow slows, ice production drops, or the filter light turns red. Some older filter setups may need an adapter. Place a cloth under the filter before removal. Check the exact refrigerator model before ordering.
BUCKET AUGER – Part Number: WR29X43990
$85.87
In Stock
BUCKET AUGER
★★★★★
★★★★★
(234)
Part #WR29X43990
The ice bucket auger is located within the ice bucket assembly in your freezer. It stirs and dispenses the ice in the bucket. You may need to replace the auger if your ice maker is noisy, or not dispensing ice. Disassembly of the ice bucket assembly is necessary to replace this part. Turn off power to the appliance before removing the ice bucket assembly to do this repair.
Temperature Sensor – Part Number: WR55X10025
$30.53
In Stock
Temperature Sensor
★★★★★
★★★★★
(69)
Part #WR55X10025
This sensor (Temperature Sensor, Thermistor, Refrigerator Temperature Sensor) sends the temperature reading of the compartment to the control board. If you notice your refrigerator is too warm, too cold, or not defrosting properly, then there may be a problem with your sensor. The temperature sensor can break from material fatigue or through normal use, and should be replaced. It is attached to the evaporator and control housing in your appliance. It measures approximately 1.25 inches long with 18 inch wire leads, and is constructed out of plastic. This part comes in white, beige. It includes the sensor, with wire leads.
Drawer Slide Rail - Right Side – Part Number: WR72X240
$49.61
In Stock
Drawer Slide Rail - Right Side
★★★★★
★★★★★
(66)
Part #WR72X240
This drawer slide rail is for the right side of your refrigerator. The drawer slide rail attaches horizontally to the refrigerator wall and supports the drawer so it can easily slide in and out. If the drawer slide track is broken, not sliding, or the fridge is not dispensing water, replacing this part could solve the issue. Make sure to unplug the refrigerator from the power source and wear gloves to protect your hands when installing this part. Refer to the diagram provided by the manufacturer for further guidance and instruction.
WATER VALVE WITH GUARD – Part Number: WR57X33326
$84.51
In Stock
WATER VALVE WITH GUARD
★★★★★
★★★★★
(87)
Part #WR57X33326
This water inlet valve (Refrigerator Water Inlet Valve Assembly) supplies water to the ice maker and the water dispenser in your refrigerator. It is located at the back of the fridge, beneath the bottom panel. It is connected directly to 2 water supplies, a wiring harness, and your inlet water tube. This part is located at the back of the fridge, beneath the bottom panel. It is connected directly to 2 water supplies, a wiring harness, and your inlet water tube. Minerals and sediments can build up over time and cause a blockage in your inlet valve. They can also cause the valve to stick open, leading to an overflow of water. If this part is malfunctioning, water flow to your appliance could be compromised. Check for small ice cubes or a lack of ice cubes/water, as this is an obvious sign the part is damaged. The water inlet valve must be replaced if the solenoids no longer have continuity or the valve has internal blockage. Test your water inlet valve with a multimeter. You can test both the water dispenser side and the ice maker side. The part measures approximately 3 inches long and 2.75 inches wide and is constructed of plastic and metal. This replacement part features 1 dual inlet water valve with quick connections. It also has 1/4 and 5/16 John Guest fittings for the outlet lines and a 1/4 compression fitting for the inlet line.
Drawer Slide Rail - Left Side – Part Number: WR72X239
$54.10
In Stock
Drawer Slide Rail - Left Side
★★★★★
★★★★★
(34)
Part #WR72X239
This is a manufacturer-approved drawer slide rail for your refrigerator. This slide rail is for the left side of the fridge. All you need to complete this repair is a Phillips screwdriver. Remove the shelves above and below the slide rail so you have room to access it. Unscrew the slide rail and replace it with the new one.
Ice Maker – Part Number: WR30X10093
$207.55
In Stock
Ice Maker
★★★★★
★★★★★
(98)
Part #WR30X10093
This 10 by 5 inch ice maker (Electromechanical Icemaker Kit, Ice Maker Assembly) produces ice. This particular model will produce seven crescent shaped cubes every cycle. It is constructed of plastic and metal, and comes in black/white. This kit includes a set of installation instructions, a 4-pin round plug-in connector, 6 post plug-in connectors, tube and fill cup. The ideal temperature of a freezer is zero degrees Fahrenheit. If the temperature in your freezer is at an appropriate level yet ice is still not being made, it could be an issue with the water inlet valve or your ice maker assembly. If you determine it is the ice maker, this is the replacement you need. The ice maker can break from normal wear and accidental damage. Ice makers will need to be replaced every 3-10 years depending on the frequency of usage and water quality. This model is mounted on the freezer wall.
Dispenser Door Assembly or Flapper – Part Number: WR17X11653
$33.60
In Stock
Dispenser Door Assembly or Flapper
★★★★★
★★★★★
(93)
Part #WR17X11653
This “Dispenser Door Assembly” (Door Recess Assembly, Ice Door Assembly, Dispenser Door, Refrigerator Dispenser Ice Chute Door Kit, Dispenser Door Flap, Ice Chute Door, Flapper) keeps the room air from infiltrating the freezer. Once the lever is pressed, the door flap opens and allows the ice to dispense into your container. If your door flapper is broken, it could allow outside air to enter the freezer and alter the inside temperature. You may notice frost buildup surrounding the dispenser area. The door flap can disconnect from the dispenser lever, or the tabs that hold it in place may break. Frequent use may distort the sealing face and cause air leaks and frost buildup. This part mounts in the ice dispenser, and measures approximately 3.25 inches in diameter. It is constructed of plastic and rubber, and comes in white/black. This part is sold individually.
Dispenser Door Solenoid Assembly – Part Number: WR62X10055
$56.33
In Stock
Dispenser Door Solenoid Assembly
★★★★★
★★★★★
(36)
Part #WR62X10055
This genuine OEM solenoid is designed for use with GE refrigerators and controls the opening and closing of the ice chute door. It serves as a direct replacement for a worn or faulty solenoid, helping to restore proper ice dispenser function. Constructed from durable metal, this part includes all necessary wiring for installation and is sold individually. Installation requires a Phillips screwdriver. Always refer to your appliance’s manual or diagram to ensure proper placement and compatibility before beginning the repair.
Bearing Slide – Part Number: WR1X2048
$18.22
In Stock
Bearing Slide
★★★★★
★★★★★
(3)
Part #WR1X2048
Sold individually.
Defrost Heater and Bracket Assembly – Part Number: WR51X10055
$92.28
In Stock
Defrost Heater and Bracket Assembly
★★★★★
★★★★★
(41)
Part #WR51X10055
The defrost heater keeps the cooling coils from frosting over. The heater will get hot and melt any ice or frost build up around the coils.
DOOR DAIRY – Part Number: WR71X38317
$42.47
In Stock
DOOR DAIRY
★★★★★
★★★★★
(77)
Part #WR71X38317
This is the replacement dairy door for a refrigerator. It is installed on the inner door and rotates up and down to allow access to the dairy compartment. It is made of clear plastic. If your dairy door is cracked, broken, missing, or won't stay on, you may need to replace it. This is an OEM part sourced directly from the manufacturer.

Questions And Answers for GSH25JGDDBB

Ask our experts a question about this model and we'll get back to you as soon as possible!

Sort by:
  • 1
  • 2
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Arthur - For model number GSH25JGDDBB
January 24, 2023
Replacement for door top shelf. Butter comp. Also light bulb for nite light on freezer door.
Chris Boyle Profile
Hello Arthur, Thank you for your inquiry. Researching the model number that you have provided, we show the dairy door as part# PS16619589 and the bulb for the freezer door as part# PS16554837. We hope this is helpful to you.
$35.22
In Stock
DISPENSER LIGHT
$42.47
In Stock
DOOR DAIRY
1 person found this instruction helpful.
Was this helpful?
Thank you for voting!
Larry - For model number GSH25JGDDBB
December 24, 2023
what is the light bulb number for the door with the control panel
Chris Boyle Profile
Hi Larry, thank you for your question! The light bulb, part number PS217532, will fit your freezer section. We hope that helps!
$21.95
In Stock
Light Bulb - 40W
Was this helpful?
Thank you for voting!
Sian - For model number GSH25JGDDBB
March 31, 2024
We need the right and left side brackets for the deli drawer
Chris Boyle Profile
Hello Sian, thank you for contacting us. The deli drawer right side slide rail for your model is part number PS306944, and the left side slide rail is part number PS306943. If you need help placing an order, customer service is open 7 days a week!
$54.10
In Stock
Drawer Slide Rail - Left Side
$49.61
In Stock
Drawer Slide Rail - Right Side
Was this helpful?
Thank you for voting!
Glenda - For model number GSH25JGDDBB
January 25, 2022
Where can i get a light bulb for the outside door water and ice dispenser
Chris Boyle Profile
Hello Glenda, thank you for your question. We have researched the model you have provided and have found the part on our site for sale and it is part PartSelect Number PS1155189. We have an installation video for you to access. We hope to hear from you soon.
$35.22
In Stock
DISPENSER LIGHT
Was this helpful?
Thank you for voting!
Kelly - For model number GSH25JGDDBB
January 31, 2023
Where do I buy a replacement bulb for the water dispenser?
Chris Boyle Profile
Hello Kelly, Thank you for contacting us. We have researched the model you have provided and have found the part you are looking for is PartSelect Number PS16554837. We hope this information helps!
$35.22
In Stock
DISPENSER LIGHT
Was this helpful?
Thank you for voting!
  • 1
  • 2

Common Symptoms of the GSH25JGDDBB

How this model fails, and the parts that fix it.

Watch our pros, then fix it yourself.

See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Refrigertor water dispenser not working BUT ice machine is working
1038 of 1163 people found this instruction helpful.
  • ralph from bristow, VA
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers, Socket set
The very first symptom here is important! The door water dispenser is not working but the ice macine is working. You may only have a frozen water tube in the door so do the following before diagnosing that your solenoid valve is bad: 1) the tube usually runs under the front of the refrigerator and usually has a quick disconnect. Undo t he connection and press the dispenser. If water comes out of the tube you have a frozen or blocked tube in the door. 2) Immediately adjust the temperature in the freezer and warm the freezer compartment as much as you can without destroying the freezer contents. Wait 24 hours. This will usually unfreeze the line. Do not waste your time with a hair dryer. NOW, if this doesn't work and you are convinced you need to order and replace the solenoid, follow these steps. Assemble your tools first. I needed a good ratchet set and a screwdriver. A shop towel is helpful for spilled water. A light is handy. Pull out the refreigerator to gain access to the rear of the unit. Unplug the power and close the water valve (older homes, you may need to actually shut the house water supply). Remove the screws which hold the cover over the lower half of the refrigerator. On the left you will see the solenoid. It's always good to see that your new part matches the one you feel needs replaced. They may not match perfectly due to changing design but they should be very similar. One screw holds this part in place and access is very simple. Now simply unplug the electrical connections. In my case, one blue "blade" type connection (powering the water) and one red "blade" type connection powering the ice maker. They are not the same size and this coupled with the coloring means you will not accidently switch them. pull the tubes clear of the solenoid. This is simple and needs no explantion. Grab your new solenoid and reattach both the electrical and water lines (two, remember, ice maker and drink dispencer). Replace the single screw. Re-attach the rear, lower refrigerator cover and go to the front of the unit to check the water. You can listen carefully and hear the power engage from the new part bringing you water. Clean up, replace the refrigerator back to its place and look really tired when your wife sees that you worked "so hard"! You probably saved at least $50-$80 from a service call which can now be used to take the family to dinner after your "exhausting" 15 minute workout of removing about 10 screws and wheeling the unit in and out of place. Writing this article took longer! My 4 year old worked harder holding the flash light!
Was this helpful?
Thank you for voting!
Plastic Auger blades broke in ice tray
586 of 630 people found this instruction helpful.
  • Tim from Newport News, VA
  • A Bit Difficult
  • 30 - 60 mins
  • Pliers, Screw drivers
I used a digital camera and photographed the assembled unit and the metal blades before I started the repair. Then, I removed the top screw on the clear shield. Flip over ice tray and removed two Phillips screws on bottom. Exterior plastic white cover comes off next. The cover sides have hard push-in white plastic tabs. Push them in; pry up top cover with small flathead screwdriver. Slide white top cover up and you will now see the metal blades and assembly. Auger is held in place with a metal c-clip and washer on the end. Use flat head screwdriver to pry off c-clip. Then you will see a nylon round slotted nut. The threads are reverse, use pliers and loosen nut. It is not that tight but pliers are needed. Then it all is loose and ready for removal. I slid all the blades off at one time and kept them stacked together. Slide out auger and clear flat shield cover. Install new auger, clear shield, and metal blade stack. When you put it all back together take a look at the long metal J-hook on the bottom make sure it is in the slot before you make everything tight. Failing to do this will prevent cubed ice from dispensing.
It is not that hard to do the repair it just takes some patience and paying attention to details.
Was this helpful?
Thank you for voting!
Fridge too warm, evaporator icing up
606 of 738 people found this instruction helpful.
  • Gerald from San Clemente, CA
  • Easy
  • 15 - 30 mins
  • Screw drivers
After replacing the defrost heater, main board and thermistor I still had the same problem. Called a repair guy and he (with the help of GE on the phone) diagnosed that the temperature sensor was bad. So I ordered from partselect and installed it and it fixed the problem. Been good for a couple months (knocking on wood). To install I had to cut the 2 wires to the old sensor, crimp the 2 new wires on and snap the new sensor to the clip on the evaporator. Very easy. Make sure you seal the ends of the wire crimps so moisture doesn't get in and corrode the connection.
Was this helpful?
Thank you for voting!