GSG746RFS3 Gibson Dryer - Instructions

replaced bearing and shaft new belt and everything works just fine

I am a "do-it-yourselfer" despite my husbands opposition. I followed instructions from one of the posts on the site and took apart the dryer. I found the location of the rear bearing and took it out and replaced it with the new one. Easy as that. Made sure the parts looked the same. Made sure I saw how everything went together. I us ... Read more ed a magnet to hold the ball bearing in place on the rear mount and taped the metal bracket on the outside of the dryer. Screwed it right in. Reassembled in reverse and works like a charm. To all the women out there who don't think they can do this. It's easy. Give it a try.

Disconnected power cord; lifted top using putty knife to open spring holds on the sides of the top; released front panel by removing screw from each side;removed old glide and glue; glued new piece in place; reconnected all parts and let dry overnight.

A caution to take care of sharp/rough edges when removing old felt and glide ... Read more . Goof Off worked well enough along with elbow grease to remove the old glue. A stonger solvent may have worked better, but did not want fumes and residue in the area.

Fit of new glide was straightforward and fit well to the lower felt glide..

(Turns out that the squeak was primarily from the rear bearing that needed some cleaning and grease, but am glad to have replaced the worn front glide)

Open the top of the dryer. Reach inside and remove 2 screws that hold the front in place. Detach the power cord inside where there is a connector. Remove the front of the dryer. That exposed the drum glide where all three nylon guides had worn off.

Peel off the old guide. Clean the surface with sandpaper. Use the supplied adhes ... Read more ive to glue on the new guide. Use masking tape to hold it while it dried.

Reverse the first paragraph to re-install.

So easy! I ordered the part on the website. Received it 24 hours later. And popped it in place. Good as new.

I took the new door catch out of the packaging and just snapped it in place it was easy peasy and took less time than opening the package

First unplugged the dryer took off the top. Removed the 2 screws holding the front panel on. Scraped and cleaned old drum glide and lower basket seal. glued new seals on replaced lightbulb while I had it apart then reassembled. It was an easy job and the wife is now happy again.. Thanks to Partselect.
Mike

Turned the knob to Start dryer one time too many and the knob broke in pieces. Got tired of using a set of pliers to start the dryer so Google was my friend. The install was quick and easy even if trying to decide what know what knob matched it took a while. But it was a perfect match (I bought an extra in case the knob on the 10 year old ... Read more washer decided to do the same thing). The price was nice, the delivery fast and now you will have repeat customer who will mention this site to their friends if they need parts.

After changing the drum support bearing, and the front felt ring, the noise continued. It turned out to be the tensioner pully. The harmonic vibration travels throughout the dryer box like an instrument so you can't tell where the sound is comming from. Before you do anything, spray a little wd40 between the bushing and the shaft on th ... Read more e belt tenioner pully. If the squeel goes away, you have found your smoking gun.

Took out of package. Used screw driver to pop off old broken handle.
Installed new part in a minute or two. Nothing to it. Was very pleased to get the part and so easy to install.

pi;; tp remove old knob, inspect and lightly lube shaft and press onnew knod. Of note Original knob had a metal brace around the shaft while the new knob has a brace inside the shaft.

I removed the broken knobs and replaced them with the fresh ones.

The amazing part of the story was that my order was placed at 11:46 AM, shipped at 2:51 PM, and arrived early the following morning. Incredible service. Thank you!

popped in one in

Removed rear cover, unplug 2 spade connectors, twist out old switch, twistin new switch. plug connectors, install cover

Took the front off the dryer and removed the old switch and put in the new one.