GSG25MIPCFWW General Electric Refrigerator - Instructions

After removing three screws on the ice bucket, it basicly came apart by itself. I needed to use pliers to remove the old nut because it had over tightened itself onto the shaft. Be careful here - it is a left hand nut - not a normal right hand nut! Reassembly was a snap putting the parts back together in reverse order. Unit has been w ... Read more orking great since the repair.

I followed the isntructions of another fellow who had repaired his ice maker, but made the mistake of taking the ice crushers apart before noting where the fixed blades were to be reassembled. Since there was not a schematic with the part I had to go on line to your site and enlarge and use the one there, while accurate, was very hard to ... Read more read and when I finished, I think it is in the wrong place as I'm not able to get the fineness of crushed ice I had before the repair, but absent a very legible schematic I'm not going to try to fix it further. The auger works, gives us ice cubes and half crushed cubes.
Another tip for future repairers is to to wait for the ice container to warm up or use a hair drier on the part where the tabs need to be depressed to slip off the blade housing. When cold it's extremely brittle, but since I had to leave the job for later at one point and left in on my work bench I found it much more pliable and easy to assemble.
All in all, I'm OK with the part and the result, but wish I could have gotten the fixed blade back into the right spot.

Removed tray, threw out ice , removed 3 screws used 2 screw drivers to seperate part & re installed

Removed the plastic frame by pushing to the inside (all 4 sides), removed touch pad by sliding it to my right and disconnected the wires. Removed the four screws that hold the dispensing unit and replaced broken parts. Please note that I also replaced the funnel. Total cost of repair for DIY $30.00, savings by avoiding repair man, pric ... Read more eless.

the only thing I had to do was slide the shelf in.. but this website saved me over $50 on the part (I got a price from my local appliance store of $80.00 and 2 weeks to get it)

Your instructions were "spot on"! Pried out broken switch with screwdriver-reinstalled new switch. Very easy! Ordered on line on a Wednesday new part arrived on following Saturday-Great service and will definately use again. Highly recommend PartSelect!

They don't make appliances like they used to. When my little butter door cracked, we kept using it until it finally fell off for good. So, where do you buy one of these? When I turned to the internet, I found a few places but they were toooo expensive. PartSelect had the right part at the right price. I figured that if I bought another li ... Read more ttle damaged part, the light cover, at the same time, the shipping cost was essentially halved, an even better deal. I was so surprised when my parts arrived faster than I expected, a couple of days by regular mail. That's faster than I could ever get a service call and who's going to call a repairman for a simple thing like that, anyway. If not for PartSelect my reputation as the Queen of Duct Tape would still be intact. I didn't want duct tape holding together my newish SS fridge in my redone kitchen. Imagine tile, granite, stainless and duct tapeI placed the little door in the fridge and now the butter stays put. the lower light shield is just as easy.

Remove rear plate. Remove fan bracket. Replace fan gaskets, blade and motor. Replace bracket. Replace rear plate. Very simple. Fixed the problem.

We soaked the new gasket in warm water for a while and we pressed it into place. Really very easy. Working fine again.
Thank you!

It originally appeared that an easy out would be required to remove ferule from piping line, but later it became necessary to cut old broken fitting off and replace with compression fitting in replacement kit. Total time to repair after all tools were on hand (needed to buy tubing cuter) was about 45 minutes.

pulled out broken bucket and auger assy. and slid in the replacement. works great so far. The easiest part was ordering the part and it didn't take very long at all to get it. Customer Service was very good at getting the job done. Thanks

Replaced defrost thermostat along with temp sensor watched the video on this page simple fix

I used pliers to pull lightly on the head of the switch, while I inserted a small flat head screw driver into the base of switch and gently worked around the edges to free it from the panel.

Replace

Empy all the food from the freezer and remove the ice container and the lower ice maker section with a 1/4 inch nut driver, unplug the unit and set aside. Remove all shelving and set aside. Remove light cover and unscrew the bulb and remove. Remove cover/with light fixture by removing the necessary screws with the nut driver. The cover h ... Read more as the fan assembly attached; unplug and remove fan assembly, remove the thermistor from coil attached with a clip. Reassemble in the reverse procedure.