GSG25MIMCFBB General Electric Refrigerator - Instructions

I had lost the provided bypass filter plug. I decided to replace it with your part.

First I removed the two screws that hold the tank in place. I then pulled the tank out about 3 inches and cut the water tubes to tank. Replaced new tank using 5/16 quick connects for water tubes.

I removed the ice bin, removed the metal rod off the bottom, unscrewed all screws holding things together and then carefully pried the crusher assembly out of the ice bin. I made the mistake of doing it when the bin was still frozen and ended up cracking it where the "clips" from the crusher are inserted. It was much easier after the bi ... Read more n warmed up.

Replaced and put everything back together.

I did it the way you recommended except rather than removing the existing tube from the water valve at the bottom of the fridge I cut the existing and new tubes and then spliced the new tube to the old tube. I already had the splicer nut so it was quicker and easier. By the way, shipping was very quick and you prices and your website are ... Read more excellent!

Followed previous instructions from a previous post. Inserted small screwdriver in the 2 outer holes up under the face plate to remove it then removed 4 screws holding the inner assembly which allowed access to the flapper assembly. Replaced it and reassembled everything. Problem solved

We couldn't get the other connector loose from one end of the tubing so he said just cut it and so we did and attached the connector. I now have water again in my fridge and took the sticky note down "don't use the water" as it had leaked for a year...... Thanks!

Your website was very easy to use and the product shipped very promptly. It was great experience. Thanks!

Removed the front panel on the door that has the ice maker controls. Removed the screws and parts. Reassembled the parts and it works better than new. Ice door closes firmly and holds tight.

I removed the screws for the inner door and removed inner lining. Then took out the ice dispenser in the door. Took off control panel on the front of the ice panel. Removed the rusted parts and put in new parts. Put all parts back the way it came apart. In retrospect.... I could have possibly replaced the parts from the front panel but by ... Read more taking apart the door...I had to thaw out the inner panel and insulation with in the door.

First, I removed all the shelves and the light guard. Second, I removed the nuts that held the fan guard and the freezer back in place (2 just under the fan guard and removed the freezer back. Third, lifted fan guard out of way (being very careful not to crack it..... cold plastic). Fourth, unpugged fan from pug then removed nuts that ... Read more held fan bracket in place...removed fan. fifth, then removed fan blade and remove fan motor from bracket, removed two wires that went to freezer light (pay attention to where they go) and installed them into the new wireing harness. Sixth, installed fan blade on new motor, bolted new assembly in fan bracket, plugged in and reistalled fan into the freezer, replaced fan guard and freezer back (reverse order of above) and then replaced freezer racks. works beautiful.

My refrigerator's initial problem was as follows:

1. Freezer fan stopped circulating the cooled air. Causing food to thaw at the top of the freezer, and freeze solid at the bottom. Ice in the icemaker thawed.

2. Water dripped from the freezer door gasket when the freezer was in defrost mode & water dispenser would no ... Read more t dispense water.

--FIX (the easy one first..):
2. I removed the inner freezer door panel and found ice filling every void of the freezer door panel-approx 5 lbs of ice dammed in the panel. I thawed the insulation and removed the ice. Also there is a styrofoam insulating surround around the inside of the dispenser panel. The styrofoam had become saturated with water and was freezing, allowing the drinking water tube to freeze, not allowing the refrigerator to dispense water...
THE CAUSE:
2. Overflowing of water from the in-door ice/water dispenser compartment reservoir (just under the grill where your glass sits, when it's dispensing water) was draining into the freezer door panel.
PREVENTION:
2. Check the reservoir more frequently to make sure water does not build up and overflow into the door.

FIX (now the trickier one..)
1. I initially thought it was the main circuit board. I replaced the board. Access is by removing the 3 hex nut screws holding door in place at the rear of the freezer. Disconnect connectors & using a needle nose pliers, squeezed the plastic catches that hold the board in place. Connect the new board (being careful not to touch the components or traces on the board) to the connectors, then snap into place using the white plastic catches.
Close everything up.

NOTE: This may, may not have contributed to the problem, but my refrigerator light went out. I replaced it with a small flouresent bulb. That bulb did not last, and became inop. Shortly afterward, the freezer started malfunctioning. I replaced the board, and the freezer was still somewhat intermittent. I replaced the bulb with an appliance 60 watt. The freezer has been perfect since...

Note: I first ordered the main circuit board, when that didn't immediately fix the problem, I ordered the above parts. I did not need the parts and am returning them. The web page is forcing me to select at least one of the parts needed for the repair, when I used neither.

I had taken the noise long enough and wanted to get this repaired. I didn't want to pay a repair man hundreds of dollars to do it so i decided to do it myself. I went on to YouTube and found a few videos that showed me how easy it was to do (very helpful).

I wasn't so sure all that noise would come from the Evaporator Fan mot ... Read more or so i ordered it and took the chance. For the small cost, it was worth the try.

All went well accessing the unit and removing the old part. Very fast indeed. However, the snag came when i went to plug in the new part electrical to the existing electrical adapters. The old part had 4 lead connections. The new part had 6. and the wires on the new part were different colors than the existing. I had to use some logic and courage to cut the wires on the new part and rewire the old adapter to this piece. Luckily, i wired everything correctly.

Calling Part Select got me a phone number for the parts manufacturer to help with the splicing but i opted to do it on my own.

The result is i have a noiseless refrigerator again. What should have taken 10 to 15 minutes took half an hour because of the wiring but overall, very easy.

While the switch did last for 9 years, the design is poor due to the failure mode. The failure should be to fail off or not able to turn on the lights which would be inconvenient but would not warm the refrigerator contents. Arcing at the contacts eventually caused the switch to "weld" closed. It is not obvious that this is occurring s ... Read more o it took some time to recognize why the temp inside the ref was high while the freezer was OK. Replacing the switch was easy once it was recognized as the problem. All that was required to replace the switch was to remove the screws holding a fiber cover and then pulling off the aluminum cap which covered the switches. Unplug the switch an squeeze the keeper on the switch to release it and pull down. Pop the replacement switch in place and plug the wires harness back in. All in all it took much less time to replace than it has to write this up. T Pope

The existing light switch was very hard to remove. I ended up having to grab it with a pair of pliers and pull it out. Once it was out, it was very easy to put in the replacement and it seems to be working fine.

used a phillips screw driver to remove two screws that held
the crusher assembly on the end of the ice bucket. Then I used the flat blade screw driver to pry the slot locks open and removed the dispenser cover. reassembly was areverse process.