GSD970--02 Hotpoint Dishwasher - Instructions

The repair went really smoothly, I found a video on youtube for how to remove the dishwasher, and the video on the parts page did a great job covering replacing the motor. The repair went really well. As others have noted, it ran really nosily the 1st time, and a little the 2nd. After that, it ran quieter, and stronger than it has in t ... Read more he 4 years we have owned the house.

I had some extra problems with my water supply line since this is an old house, but I won't dwell on that. If you have an older model like mine (probably 80's) the only trick is with the drain solenoid. The kit uses a newer style solenoid that is a little different. Without getting too technical here, let me just say that if the old solen ... Read more oid has a little metal lever that is actuated when the plunger goes down do not discard it. From what I have read, the dishwasher will shut down with an error code if you don't use this part and you will also have 2 wires that are just hanging there with nothing to plug in to. You will need to use an included metal plate and screws to adapt that part to the new assembly. It takes a little mechanical aptitude, but after you figure it out it works perfectly. I did not see this mentioned in the instructions but the necessary parts were included. Replacing the pump and motor was fairly simple, and all the needed parts were included in the kit. I did remove the unit from under the counter and lay it on it's back for easy access to the pump and motor. It helps to watch some You-tube videos if you are unsure about how to do this, but make sure they are working on the brand you have. All dishwashers are NOT the same.

Turn off the power at the breaker panel. Turn off the water supply that goes to the dishwasher. Remove the front lower panel to gain access to disconnect the water line and electric. Now remove the two screws that connect the dishwasher to the countertop. You should be free to slide the dishwasher from under the countertop far enough to r ... Read more emove the drain hose. Slide the dishwasher out all the way and lay on the floor door down. Loosen the two clamps that hold the motor up. Remove the motor bracket, (should only be one screw. Disconnect the wires from the motor. Now just pull the motor down and out. Repeat the process to install the new motor. I took several pictures before I started removing anything. The instruction that comes with the kit is very good. Their will be parts in the kit that will not be used. Not to worry!

Too easy- what made it easier was this is a portable roll-around unit I could lay on it's back. Loosen the two clamps around the washer pump, hook up the drain solenoid, washer motor wires, attach the motor hanger, that's basically it. It took longer to make sure I was working from the right set of instructions- this pump covers several ... Read more models. Once I had that right, it was really a snap. Now the unit is so quiet. It once sounded like a jet engine in the kitchen, now it runs so quiet you can hear the water splashing around inside- a big improvement. We should be able to hang onto this thing for a while longer.

I removed the seven screws from arond the door. I pulled off the old gasket and replaced with the new one. I then replaced the seven screws. I had to removed the top screws again since I did not get the lever aligned properly. Once that was corrected then dishwasher works with no leaks.

This was really easy. The parts fit perfectly. First i turn off power at circuit panel; turn off water and dissconnected water line and discharge hose. Removed dishwasher from under counter and placed on side. Disconnected connections to motor and pump and replaced and installed same as one unit.

Most difficult part of repair was getting dishwasher out and in under the cabinet. Especially, feeding the copper water line from under the sink and then back while trying to align the connection. Installing the part itself was easy with good instruction for taking it off and reinstalling. However, since the motor had been upgraded, it ... Read more required new connections. The connections were provided for this, but no instructions for the electrical connections.

Dishwasher is 22 years old and I'm 80 years old so it took longer, about 3 hours. After removing, turned upside down and removed old pump-motor assembly and replaced with new following directions [which took a little while to figure out; my assembly was quite a bit different from the replacement pump-motor]. Pleasantly surprised at how ... Read more quiet the dishwasher now runs. Normally I would replace this old an appliance, but this unit has provision for inserting a wood panel that blends with the cabinets and a new GE dishwasher with this feature costs $1300 MSRP. I'm trying to save money for when I get old so I decided to do the repair myself. For $150 it was a worthwhile investment.