GSD2100R20CC General Electric Dishwasher - Instructions

Unsnapped clip,and moved it 90 degrees. Slip wheel and clip off. Installed clip on new wheel. replaced new wheel. The wheel did not come with a new clip and was not suggested on the parts list. The existing clip was still OK but if it was not, I would have had to order a clip and wait. All in all, a good experience.

The wheels came with a clip on part that clipped to the rack and the wheel snapped into that clip. I am a woman and it was easy for me to do. Thanks to Parts Select for being an easy to use and navigate site, for quick shipment and for good directions with the parts. Sincerely, Teresa from Alabama.

First off on this model, if one of the telescopic spray arm weld assembly comes out it is NOT repairable you have to replace the whole part.
The assembly on my model number was simple you do NOT have to PRY anything out...(I broke the base spray arm trying to shove a screw driver into the Spray arm weld.(You could try this but chanc ... Read more es are the plastic will break and I recommend replacing both parts why not???.)
There are two bolts on the sump protector basket that has to be removed first. They are 1/4 inch.
Once that cover is free there is a bolt (also 1/4 inch) on the base spray arm it is easy to see but hard to get to I used a very thin open ended wrench
1/3 turn at a time till I could get the socket on it.
Next there is a rubber gromet like thingy that just pulls loose remove it also.
Next take the spanner wrench (I used one with a rubber belt) wrap around base spray arm and turn counter clockwise it just unscrews.

reassembly is simple but this is GE so I inspected the sump and found one medal impeller and one black screw at the bottom!!!!!
The impeller is threaded and just screws onto the shaft (look at the diagrams on this web site to see placement.)
Throw the screw away it does nothing except if left there jacks up the impeller I am guessing it fell out of some factory workers pocket.
If after you put all the parts back in and the washer does not drain check your reassembly if you don't line the parts up just right the unit will not drain.
Don't forget the rubber grommet (not sure what it does but it's easy to replace after all is assembled) also there is a metal washer that is inbetween the base spray arm and the spray arm weld put it back before you click those two parts together it protect the plastic from wearing it is a bearing!!
If you found this site you are doing really good This site had all the diagrams I was looking for I love you guys you so rock!!! I wish the diagrams were bigger but they were adequate. GE 's site was no help and I doubt I will ever buy another one from them.
Good luck just remember look at the parts diagrams before attempting the repair.

replaced rack, no repairs required

You'll need to remove the front toe kick and (if installed, the GE Profile baffling for additional silencing action).

You will need to disconnect the right wire connection to access the right screw (and may need to use a flat head screwdriver). You can then remove the 2 screws that hold the Valve Water Inlet on.

... Read more >You will then need to loosen and the hose clamp that attaches the water line to the Valve Water Inlet. You may need to force it undone since the rubber connection is pretty secure around the water tube inlet.

Disconnect the plastic wire housing from the Valve Water Inlet and you should now have the Valve Water Inlet disconnected.

Reverse the order and reconnect everything and you should be good to go!

Double-check for any leaks prior to pushing everything back in :)

Siimply removed the rack and replaced the wheel assembly. Very easy

Very easy about 5 min replacement, Checked electrical conductivity to verify I had a bad solinoid, after I received the new part. I removed and replaced part by only removing and re-installed 2 screws and spring. Dishwasher worked like new.

Repair easy. . Snap it in. . . . . . Impressed with the speedy delivery. Thanks

Simply discarded old wheel assembly and snapped new wheel assembly in place. Very simple.

It was easy as pie. The new wheels came with the new axles already attached, and the whole wheel just snapped onto the lower rack. I ordered 6 and they arrived quickly and attached within minutes, and the dishwasher actually works better now that the rack is raised properly. Thank you!

First I had to unscrew screws under the counter then pulled built in dishwasher out from under the counter, attached hing arm link to right side bracket on door, and the other end I attatched to a spring at the back of the unit. Thats it! and pushed the dishwasher back into place. All back to normal....by the way Im a 67 yr old great gra ... Read more ndmother...

Ordered the part, by using the diagram on the ge website identified the part and ordered it right them and when it came (delivered really fast) took it out of the bag and screwed it in the jet dry despenser and is working great.

Opened door, removed screw holding down metal plate that presses against interlock switch when door is closed. Removed plastic cover thingy that is over interlock switches. Removed the interlock switch by pressing the plastic lock thingy away from switch. Pulled the wires off each end of the interlock switch. Removed new interlock switch ... Read more from plastic bag and reversed above procedure. Done, shut door and the dishwasher works.

The repair only required me to lift out the old unit and set the new rack into the dishwasher. I was pleased that there was nothing to put together. The rollers were already attached.
It took longer to open the shipping box than to do the installation.

A no brainer. Simply open dishwasher door, remove lower rack and set new rack in place. Roll the new lower rack in dishwasher and close door. It fit perfectly and life routine was instantly on it's way without disruption.