EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

GRSR3620SM-2 General Electric Range - Instructions

All Instructions for the GRSR3620SM-2
1 - 15 of 37

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Coil Burned Out
63 of 94 people found this instruction helpful.
  • Frank from St Augustine, FL
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Open lid,un screw coil,pop in new coil snap holders in place,then cook a steak
Was this helpful?
Thank you for voting!
Heating element burned out.
41 of 62 people found this instruction helpful.
  • LANCE from ORELAND, PA
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Unplugged range. Opened oven door and removed two screws from top of oven opening. Lifted oven top and propped up
with a 2 x 3.Unscrewed the two screws that were holding
Was this helpful?
Thank you for voting!
Oven Door Bracket Broke
14 of 23 people found this instruction helpful.
  • Scott from Columbia, MD
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
After several temporary fixes, one of the end caps finally broke completely, so the handle fell off. Ordered both caps, they arrived remarkably fast, and were installed easily.
Was this helpful?
Thank you for voting!
The small burner inside the double burner shortd out.
5 of 5 people found this instruction helpful.
  • david from PORT ORANGE, FL
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers, Socket set
The first thing was to watch U-Tube . The replacement burner was being
replaced in a GE glass top range. Exter tools were required than depicted
in the U-Tube project. The project overall was not dificult for me however I was a general contracter for over 25 years
Was this helpful?
Thank you for voting!
replaced door handle and end caps
4 of 5 people found this instruction helpful.
  • Thomas from COXS CREEK, KY
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
the first end cap broke when I tried to tighten the screws, the end cap holes were too small, Thirty some dollars down the drain. Drilled out the second end cap before I tighten the screws, worked fine. Make sure you drill out the holes of the end caps or they will split out and you lose your money. There are no warnings about this proble m.
Was this helpful?
Thank you for voting!
Small front burner on our glass top stove died.
3 of 3 people found this instruction helpful.
  • Robert from FLEMING ISLE, FL
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Robert did not do the repairs. I did! 70 year old housewife. I watched a Utube video and thought I could certainly handle that. Ordered my part from your site. It came in two days. Burnet was replaced in under 20 minutes by me! Anyone can do this. Super easy, parts just plug in.
Was this helpful?
Thank you for voting!
remove and replace
10 of 24 people found this instruction helpful.
  • Perry from Flushing, NY
  • Really Easy
  • Less than 15 mins
very easy remove the bad bulb install the new one
Was this helpful?
Thank you for voting!
bottom trim had rusted, so we needed new piece
3 of 4 people found this instruction helpful.
  • Robin from Apple Valley, MN
  • Really Easy
  • Less than 15 mins
  • Socket set
Removed oven door (made sure hinges were locked open and stayed open). Remove part on top of trim, removed rusted trim and replaced with new trim. Replaced part on top of trim and screwed all back together. Put oven door back on and unlocked hinges. It was easier than the trial run (when I hadn't realized that the hinges weren't locked op en!)
Was this helpful?
Thank you for voting!
replaced more for cosmetic reasons
4 of 7 people found this instruction helpful.
  • Glenda from Port Richey, FL
  • A Bit Difficult
  • 1- 2 hours
  • Screw drivers
Your support team helped tremendously in ordering the parts. Parts arrived in only 2 days. Upon taking the door off the oven we had to remove several screws, then more screws. Was able to take it almost fully apart, replace old broken parts with new. Putting it back together was like a puzzle. We did it though and saved money! Thanks
Was this helpful?
Thank you for voting!
rusted trim strip
3 of 5 people found this instruction helpful.
  • Larry from Sarasota, FL
  • Really Easy
  • 15 - 30 mins
  • Socket set
remove screws, re-install screws
Was this helpful?
Thank you for voting!
No Spin Cycle
2 of 2 people found this instruction helpful.
  • Richard from LORDSBURG, NM
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Lid Switch.
Rewiring connection.
Function is satisfactory.
Fan belt ordered is saved.
A 1970 Clothes Washer.
Was this helpful?
Thank you for voting!
Both end caps were broken removed
2 of 2 people found this instruction helpful.
  • Johnson from LUFKIN, TX
  • Very Easy
  • 15 - 30 mins
Removed torx head screws. Removed broken pieces of the end caps. Replaced the handle installed the end cap screws.
Was this helpful?
Thank you for voting!
The trim piece on the bottom of the door was rusted making the unit look really dirty and used.
2 of 2 people found this instruction helpful.
  • Glenn from West Melbourne, FL
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
It was pretty simple. Just remove the door as the bottom piece holds all the parts together. Place on table top and remove old trim. Install new trim and install door. The only difficult part was the trim had a space for the glass door front. I opened up the space so that the glass would seat easier. Went together real easy. Stove looks like it's brand new.
Was this helpful?
Thank you for voting!
The end cap door handles on our range were broken.
2 of 2 people found this instruction helpful.
  • Gordon from IOWA CITY, IA
  • A Bit Difficult
  • 15 - 30 mins
  • Nutdriver, Screw drivers
The parts were shipped quickly and were what I ordered. The one suggestion I would make to the installer would be to drill out the insert holes a bit in the plastic columns in the inside of the bracket. There are two such columns and they are used to provide further strength to the end cap. However, the diameter of the screw is too large for the insert hole because as I installed the first bracket one of these columns broke. After drilling out the insert hole, the screws were still snug and the end cap (and door handle) was quite solid.
Was this helpful?
Thank you for voting!
Part rusted over time...22 years.
2 of 2 people found this instruction helpful.
  • Jeannene from HUNTINGTON, TX
  • Very Easy
  • Less than 15 mins
  • Screw drivers
Unscrewed eight screws. Removed rusted part. Cleaned area with Windex. Replaced new part.
Was this helpful?
Thank you for voting!
All Instructions for the GRSR3620SM-2
1 - 15 of 37