Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Blower motor out on condenser
4 of 7 peoplefound this instruction helpful.
George from WHITE BIRD, ID
Easy
30 - 60 mins
Screw drivers
followed detailed movie from Utube video
Was this helpful?
Thank you for voting!
Refrigerator did not run. It made several rapid clicks, then silent, then a minute later more clicks.
3 of 4 peoplefound this instruction helpful.
John from OCEAN SPRINGS, MS
A Bit Difficult
1- 2 hours
Pliers, Screw drivers
I removed the lower back panel. The difficulty and time consuming part was finding the old parts. They were inside a cover on the side of the motor. The cover was difficult to remove. It slides away from the motor. The terminals on the replacement parts were oriented differently from the original, Like a mirror image. Accordingly,
... Read more I reversed the wires (side to side) and connected them to the replacement parts. The refrigerator is now working fine.
Door switch would not turn on interior refrigerator light.
3 of 4 peoplefound this instruction helpful.
Jane from SHORELINE, WA
Very Easy
Less than 15 mins
I had previously watched a YouTube video (do this first!!) on a similar Kenmore model so I knew what to look out for: (1) turned off power, (2) took thin putty knife to slip under outer lip of switch (most screwdrivers are too thick), (3) wiggled switch at front end to release the tab, (4) unplugged from the socket, (5) plugged in new sw
... Read moreitch, (6) popped new switch back into door, (7) turned on power. Voila !! Super easy. I couldn't believe it.
Read less
Was this helpful?
Thank you for voting!
Pops right in
2 of 2 peoplefound this instruction helpful.
Darlene from MISSION HILLS, CA
Very Easy
15 - 30 mins
Screw drivers
Pops right In
Was this helpful?
Thank you for voting!
Switch stops working
2 of 2 peoplefound this instruction helpful.
David from PENNSVILLE, NJ
Easy
Less than 15 mins
Pliers, Screw drivers
Replace with new switch. this is the third switch i have replaced in 10 years. the only part, besides a light bulb, that has gone bad. obviously this is a problem with this model for Kenmore, or just poor switch design.
Was this helpful?
Thank you for voting!
light didn't come on when the door was opened
2 of 2 peoplefound this instruction helpful.
William L from SUMAS, WA
Really Easy
Less than 15 mins
Screw drivers
I took a very thin bladed screwdriver and took the old part out -carefully. The new part fit in quite easily.
Was this helpful?
Thank you for voting!
Replaced hose and it was exactly what I needed.
3 of 5 peoplefound this instruction helpful.
Donald from CLEBURNE, TX
Very Easy
30 - 60 mins
Screw drivers
Replaced old hose and installed the new one. Was very simple with the instructions in your email..... step by step, could not of been any similar.... you guys rock
Was this helpful?
Thank you for voting!
Freezer frost accumulation
3 of 5 peoplefound this instruction helpful.
Peter from Sewell, NJ
Easy
30 - 60 mins
Screw drivers
After noting frost in freezer Right rail started to jam. Noted freezer door was closing crooked. Rail replacement resolved issue. It had been frosting up for some time so Rail must have been broken for a while. Check door seals they were not closing flush.
Was this helpful?
Thank you for voting!
Leaking
2 of 3 peoplefound this instruction helpful.
Johnny from MOUNT OLIVE, AL
Really Easy
30 - 60 mins
Screw drivers
Swapped old one with new one. New one had extra plug not needed.
Was this helpful?
Thank you for voting!
Light switch for refrigerator not functioning
2 of 3 peoplefound this instruction helpful.
shirley from ONALASKA, WI
Easy
30 - 60 mins
Screw drivers
Followed instructions online
Was this helpful?
Thank you for voting!
rail broke
3 of 6 peoplefound this instruction helpful.
Ronette D from KOKOMO, IN
Really Easy
Less than 15 mins
slid out the old one and slid in the new one.
Was this helpful?
Thank you for voting!
Door light switch, 3rd one I have replaced in 6 years made in China.
1 personfound this instruction helpful.
Charles from CURWENSVILLE, PA
Really Easy
Less than 15 mins
Pliers, Screw drivers
Easy install, small screwdriver under back of old switch push out and pull out with small pliers. unsnap the old plug and install new. YOUR DONE
Was this helpful?
Thank you for voting!
Replace switch
1 personfound this instruction helpful.
Dean from HILLSDALE, MI
Really Easy
Less than 15 mins
Screw drivers
Read previous tips Taped off area around switch to protect surface Used putty knife to extract switch Used screwdriver to separate connector from switch Plugged in connector Pushed switch assembly into opening Removed tape
Was this helpful?
Thank you for voting!
The switch became intermittent - Possibly a poor designe
1 personfound this instruction helpful.
Sidney from ENDICOTT, NY
Very Easy
Less than 15 mins
Screw drivers
Used a small screw driver inserted into the front of the switch (facing the front) and pried until the switch was coming out. When out, I removed the connect harness and replace the switch with a new one.
Was this helpful?
Thank you for voting!
replace refrigerator ice bin because old bin would not dispense ice.
My Orders
