GM21506 Homelite Trimmer - Parts

This spool retainer is sourced from the equipment manufacturer for use in trimmers. It is a plastic knob, measuring 2 inches in diameter, with a threaded metal bolt in the center. The retainer has a right hand thread, and it is used to secure the spool within the trimmer head to prevent it from coming loose during operation. The retainer ...Read moreengages with the trimmer head to lock the spool in place, while it also advances the cutting line for greater cutting efficiency. If the threads on the retainer bolt wear out or the plastic body becomes damaged, the retainer will be unable to engage with the trimmer head, causing the line to tangle, the spool to come loose, and lowering the cutting performance of the trimmer. Remove the trimmer head cover and detach the retainer from the assembly. Position the new spool retainer in the assembly and thread it firmly into place.

This grass deflector acts like a shield so that grass clippings are directed away from you and the surrounding areas while you are operating your trimmer. It is often located near the bottom of your trimmer, close to the cutting head. This assembly also includes the line cutting blade, which maintains the proper length of the trimmer line...Read more. If the assembly is cracked, bent, or missing, grass clippings may fly in unintended directions. This can be dangerous if your trimmer throws debris towards you or others nearby, so it is important to replace the damaged deflector. To replace the assembly, you will need a screwdriver to remove the flat washer, wing nut and, the hex screw from the grass deflector. Please be aware that this OEM grass deflector is sold individually.

This OEM spring, also known as a recoil or rewind spring, is housed in a container and is used to retract the starter rope on various lawn equipment models. Over time and through use, the spring will eventually lose its tension, and will break. If your starter rope has no resistance when pulling it, the starter spring is likely broken. Me...Read moreasuring at approx. 3-inches by 3-inches, this spring is suitable for use with a variety of lawn equipment models and is sold individually.

This carburetor gasket is an OEM replacement part for use in a variety of lawn and garden outdoor equipment. It seals the area between the carburetor and the intake manifold to prevent air and fuel from leaking. Over time, the gasket may wear down, crack, or warp due to normal aging, exposure to heat and chemicals, or improper installatio...Read moren. A faulty gasket will cause air and fuel to leak, resulting in hard starting, rough idling, fuel wastage, and overall lower engine performance. To replace the gasket, remove the air filter cover, air filter, and carburetor. Carefully pull off the old gasket, and thoroughly clean the sealing surface of all residues. Place the new carburetor gasket onto the intake manifold, and firmly press it in place. Reassemble the equipment parts in reverse order to complete your repair.

Genuine OEM replacement part, this part is sold individually. This part is where the stringhead assembly is mounted on the Trimmers shown below. It attaches to the spindle. The thread mount on the spindle is a left hand thread.

This is a genuine manufacturer-sourced component that is specially designed for use with Ryobi, Ridgid and Homelite equipment. It is an identical replacement for a missing or faulty switch that was originally installed on a new unit, please make sure to refer to the appropriate diagrams of your model for the correct location and applicati...Read moreon of this item. Keep in mind this high-quality plastic body switch is sold individually.

Genuine OEM replacement part, this item is sold individually. This part is installed in between the carburetor and the air box cover It is the Air Filter for the outdoor equipment listed below. It has a fine mesh material for the Air Filter. Once this filter gets dirty and or clogged it can be blown clean or brushed clean. If it develops...Read more a hole in it or gets torn, it should be replaced ASAP, or it could cause damage to the carburetor and engine.

Genuine OEM replacement part, this item is sold individually. This is the part of the trimmers listed below that the cutting line is installed in. This spool uses .095 diameter cutting line. If you would like to obtain the complete cutting head assembly with the line already installed, order part number 309562002

Genuine Ryobi replacement part, this item is sold individually. The Air Box Cover is placed over the Air filter Base. It has air vents in it to provide air so the carburetor can receive an ample supply of air to operate properly. It also partially covers the carburetor to help keep it clean from debris and foreign material.

This replacement fuel cap assembly is specially designed for use with Homelite and Ryobi trimmers. It is an authentic part that is supplied directly from original equipment manufacturer. It is used to keep the fuel in the tank. This fuel cap is made out of plastic and it is sold individually.

Genuine OEM replacement part, this item is sold individually. The purpose of the 901551001 Intake Gasket is to create a seal between the Heat Dam and the cylinder head. Over time because of the heat it is exposed to this gasket will deteriorate and will have to be replaced.

It is an authentic replacement ignition module. It is sourced from original equipment manufacturer for use with Ryobi trimmers/brushcutters. The purpose of an ignition module also known as armature-magneto is to provide electric current for the ignition system by producing pulses of high voltage for the spark plugs. It is made out of meta...Read morel with rubber spark plug boot. Includes one (1) module per order. To complete this repair you would need screwdriver set. • Remove the spark plug boot • Remove the air filter housing • Remove other shrouds/housings • Disconnect ignition wires • Disconnect spark plug boot • Face flywheel magnet to ignition module position • Install new module in place • Reassemble and test the unit