EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

GLGFZ376FCC Frigidaire Range - Instructions

All Instructions for the GLGFZ376FCC
16 - 30 of 133

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Range would start beeping and needed to be unplugged.
15 of 18 people found this instruction helpful.
  • George from TURNERSVILLE, NJ
  • Very Easy
  • Less than 15 mins
  • Nutdriver
Remove 4 screws on back panel. Unclip wire connector and remove probe and install new probe.
Was this helpful?
Thank you for voting!
oven bottom had foil stuck on it would not come off
15 of 19 people found this instruction helpful.
  • ronald from brownsburg, IN
  • Really Easy
  • Less than 15 mins
  • Screw drivers
First I removed the two screws that hold the bottom panel I then pulled the panel out and put the new panle in and put the two screws back in
Was this helpful?
Thank you for voting!
replacing the fan on a convection oven (fan was making a vibration noise)
17 of 26 people found this instruction helpful.
  • John from Stevensville, MD
  • A Bit Difficult
  • 30 - 60 mins
  • Pliers, Screw drivers, Socket set
This was the first time replacing the fan. It is a lot easier to work in the oven compartment with the oven door removed, only two screws on the door and the hinges were released. I found that a couple of the screws were either rusted or stripped so I used a pair of pliers to remove the screws that were holding the diffuser in place. O nce there was access to the fan I found that the fan was warped and that the blades were scraping against the back wall of the oven. The next challenge was to remove the retaining nut. I used a sheet metal screw to secure the warped fan to keep it from spinning. once I figured out that you have to turn the retaining nut to the right to loosen, it came off easily. 1/2" socket with extension. When I replace the fan I used two washers for spacers to make sure that the fan would not scrape the wall of the oven. Its been tested many times and the oven does not make that horrible sound anymore.
Was this helpful?
Thank you for voting!
The burner knobs were lose and kept falling off.
13 of 15 people found this instruction helpful.
  • J Andrew from Richmond, VA
  • Really Easy
  • Less than 15 mins
Pull off the old knob, and slide the new knob into place. Less than 10 seconds for each knob.
Was this helpful?
Thank you for voting!
Regulator had propane leak past diaphragm
14 of 19 people found this instruction helpful.
  • Albern from Bainbridge IS., WA
  • Easy
  • 30 - 60 mins
  • Nutdriver, Wrench set
removed two screws disconnected inlet pipe and two outlet pipes, removed regulator. Replaced with new regulator. performed leak Test.
Was this helpful?
Thank you for voting!
Handle on oven door broke
18 of 33 people found this instruction helpful.
  • KELLY from LAKELAND, FL
  • Really Easy
  • Less than 15 mins
called around and way to much money for repair man as well as parts from local appliance repair store. They wanted 10.00 for a screw that we got from you for $3.00 same as all the other parts saved over 70.00 dollars.

quick delivery and easy repair ... like new again .

would use you again
Was this helpful?
Thank you for voting!
Right front ignitor would not light
12 of 16 people found this instruction helpful.
  • Terry from Acton, MA
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
Removed grates and range cover, unscrewed all sheet metal screws and removed cover plate. Disconnect electrical connector and then removed old ignitor/orifice ass and replaced it with the new one. Replaced all screws in cover plate and then reattached range cover and grates. Turned on the gas and it lit after a few sparks took place.
Was this helpful?
Thank you for voting!
Oven would not ignite, gas smell, igniter glows
11 of 13 people found this instruction helpful.
  • John from PORT JEFF STA, NY
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Socket set
Disconnected power, I removed the igniter from oven. Measured the resistance (275 ohms) and then the current draw. DO NOT ATTEMPT THIS UNLESS YOU ARE ABLE TO ACCOMPLISH THIS SAFELY. I made a harness and connected the old igniter to 110 V ac, Current draw thru the meter settled at 2.7 Amps. Too weak to fully open gas valve. Valve require s 3.2 - 3.6 amps to fully operate properly. New igniter measured 300 ohms and current draw was 3.4 amps. Installed new part and everything works fine. Correct part and good service from this site
Was this helpful?
Thank you for voting!
lost the metal clip inside the knob. so knob was loose
9 of 12 people found this instruction helpful.
  • Jacob from Farmingdale, NY
  • Really Easy
  • Less than 15 mins
I compaed price at different sites and partselect .com was 30% cheaper for the same item. I received the part in 2 days by fed-ex.
Doing the job was real easy.Just pull the old knob out and put the new one in.
Was this helpful?
Thank you for voting!
broken ceramic burner element
9 of 12 people found this instruction helpful.
  • Phillip from Saint Simons Island, GA
  • Really Easy
  • Less than 15 mins
Simple: remove the element by hand and replace new one.

I can't believe how quickly I received my new part -literally next day.
Was this helpful?
Thank you for voting!
Oven light bulb went dark; it needed replacing
10 of 17 people found this instruction helpful.
  • Lise from CEDAR GROVE, NJ
  • Very Easy
  • Less than 15 mins
Twisted replacement bulb into place easily. Let there be light!
Was this helpful?
Thank you for voting!
the new burners had no threads for the screws
6 of 6 people found this instruction helpful.
  • Steve from NORTH PEKIN, IL
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Wrench (Adjustable)
had to use a tap and cut new threads. Also had to remove the top of the range, and the metal cover under the top.
Was this helpful?
Thank you for voting!
broken lens over oven light
11 of 22 people found this instruction helpful.
  • Leslie from Warsaw, VA
  • Really Easy
  • Less than 15 mins
Your service was OUTSTANDING...Ordered one afternoon, and before lunch time the next day, the delivery man rang my door bell...Thanks a bunch for you excellent service.....
Was this helpful?
Thank you for voting!
Rusted leveling foot
6 of 9 people found this instruction helpful.
  • Melinda from Three Rivers, MA
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers, Socket set, Wrench (Adjustable)
I couldn't unscrew the leveling foot because it was rusted and corroded. The bracket holding it was easy to remove so I took the bracket with the corroded foot off and replaced it with the new foot and bracket. Very simple. I made sure I oiled it so it wouldn't rust again.
Was this helpful?
Thank you for voting!
burnt in aluminum foil...unable to remove
5 of 6 people found this instruction helpful.
  • Michael from Lamoni, IA
  • Really Easy
  • Less than 15 mins
took the two screws out by hand, slipped out the ruined panel, slid the new one in place, replaced the two screws...simple as that
Was this helpful?
Thank you for voting!
All Instructions for the GLGFZ376FCC
16 - 30 of 133