- Home
- GLGF386DBM
- Instructions
GLGF386DBM Frigidaire Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Oven would not heat or sometimes hold heat to set temp
2 of 2 people
found this instruction helpful.
-
TRACY from NEW PHILA, OH
- Easy
- 15 - 30 mins
-
Nutdriver
I was able to find the most common reason for my oven's symptom by searching online. I searched for the part I needed but was not confident that I would get the correct part until I looked on partselect.com. After verifying the part number with my owners manual and looking at the video on their website, I decided to order. PartSelect ship
... Read more
ped the part as expected, and I was able to install it in less than 30 minutes. The only tool needed for installation was a nut driver. My oven is now working like new.
Many thanks to PartSelect for their comprehensive website and fine service.
Many thanks to PartSelect for their comprehensive website and fine service.
Read less
Was this helpful?
Thank you for voting!
oven was over heating temp. of oven keep climbing
2 of 2 people
found this instruction helpful.
-
Herbert from MARIETTA, OH
- Very Easy
- Less than 15 mins
-
Nutdriver
removed screws from back cover then pulled elect. plug apart. removed screw pulled out probe installed new probe put cover back on very easy only problem was that it said that 88% of time would fix the problem. will this time it didn't work oven still over heating.
Was this helpful?
Thank you for voting!
old knob fell off
2 of 2 people
found this instruction helpful.
-
Gloria from DALLAS, TX
- Very Easy
- Less than 15 mins
order anew knob, put it on
Was this helpful?
Thank you for voting!
bottom oven plate had foil stuck to it
4 of 9 people
found this instruction helpful.
-
Wilma from Syracuse, NY
- Really Easy
- Less than 15 mins
-
Screw drivers
Very easy to order,part was delivered promptly and installation was easy.I unscrewed a few screws and lifted the bottom panel out and put the new one in.
Was this helpful?
Thank you for voting!
Oven temperature was not consistent.
2 of 3 people
found this instruction helpful.
-
Kimberly from OWASSO, OK
- Really Easy
- 30 - 60 mins
-
Nutdriver
I pulled the oven away from the wall, unplugged the cord, removed the back panel then removed the screw from the old sensor.
Was this helpful?
Thank you for voting!
Oven taking along time to heat up
2 of 3 people
found this instruction helpful.
-
don from GOLDENDALE, WA
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
First thing. If your wife insists on helping buy 2
Because the first one will mysteriously come up broke. Just saying
This is a very easy replacement project. You can do it. TURN POWER OFF TO RANGE BEFORE REPLACING IGNITER Remove a couple screws take the heat shield out. Remove the bottom drawer unplug the igniter remove a cou ... Read more ple screws holding the igniter in place. Replace the igniter and screws. Plug in the igniter replace bottom drawer. Screw heat shield back down. Turn power to stove back on. You’re done
Because the first one will mysteriously come up broke. Just saying
This is a very easy replacement project. You can do it. TURN POWER OFF TO RANGE BEFORE REPLACING IGNITER Remove a couple screws take the heat shield out. Remove the bottom drawer unplug the igniter remove a cou ... Read more ple screws holding the igniter in place. Replace the igniter and screws. Plug in the igniter replace bottom drawer. Screw heat shield back down. Turn power to stove back on. You’re done
Read less
Was this helpful?
Thank you for voting!
Gas stove won’t light on half the appliance
4 of 9 people
found this instruction helpful.
-
Julieta from ELMIRA, NY
- A Bit Difficult
- 1- 2 hours
-
Screw drivers, Socket set
First we replaced the wiring harness because a multi-meter said it wasn’t getting power. That was only partially true. The wiring harness was burned looking so we just kept it instead of sending it back. When the spark module got here the burner caps were removed and then the wires were noted where they went on the module and then the pow
... Read more
er and gas were turned off. The spark module was removed and then the stove was tested and we were back in business.
Read less
Was this helpful?
Thank you for voting!
Oven igniter stopped working
1 person
found this instruction helpful.
-
Darin from O FALLON, MO
- A Bit Difficult
- 1- 2 hours
-
Nutdriver, Pliers, Screw drivers
When removing the screws that hold the igniter, the screws stripped. Not my first time so I very slowly removed the screws but they still stripped. I had to cut both with a small hacksaw but be careful not to damage the bracket that is welded to the burner. After successfully removing the screws had to go get 5/16 steel self tapping screw
... Read more
s to install the new igniter. Use a self tapping screw to thread the hold first then remove and install the igniter with a new screw. Job was a success. Good luck with yours
Read less
Was this helpful?
Thank you for voting!
Broken burner knob
1 person
found this instruction helpful.
-
Dolores from SAN ANTONIO, TX
- Very Easy
- Less than 15 mins
Received new knob simply inserted and it worked perfectly!
Was this helpful?
Thank you for voting!
Panel finish ruined by tin foil
1 person
found this instruction helpful.
-
Barry from MOORE, OK
- Easy
- Less than 15 mins
-
Screw drivers
Removed both oven racks the removed two screws in back. Lifted rear of panel until front lip of panel was free. Installed new panel in reverse order. I was recycled the old steel panel at our local recycling station.
Was this helpful?
Thank you for voting!
Replacement of bottom oven panel
1 person
found this instruction helpful.
-
Eileen from AKRON, OH
- Very Easy
- Less than 15 mins
-
Screw drivers
Very simple. I removed the oven racks, loosened the two screws that held the old panel in place, lifted out the old panel and replaced it with the new one, then tightened the screws to hold the new panel in place. It took no more than 10 minutes.
Was this helpful?
Thank you for voting!
The know was missing
1 person
found this instruction helpful.
-
Claude from PORTLAND, OR
- Really Easy
- Less than 15 mins
So easy... just put the knob in place.....
Was this helpful?
Thank you for voting!
Oven bottom panel
1 of 2 people
found this instruction helpful.
-
Maria from NEW ORLEANS, LA
- Very Easy
- Less than 15 mins
-
Screw drivers
Unscrewed old panel/removed and inserting new panel and used same 2 screws to secure in place.
Was this helpful?
Thank you for voting!
Burner knob broke.
2 of 5 people
found this instruction helpful.
-
ERICA from PHILADELPHIA, PA
- Very Easy
- Less than 15 mins
It was easy to find on the website. It doesn't match exactly, however without the knob the burner will not light. It was literally a snap to snap the knob in place. The part arrive in a timely manner from the USPS. Thank you! I'm encouraged to get one more piece of equipment repaired because of this site thorough service.
Was this helpful?
Thank you for voting!
Oven would not reach temperature or it would finally reach temp but would not stay warm.
1 of 2 people
found this instruction helpful.
-
Craig from FAYETTEVILLE, NY
- Really Easy
- Less than 15 mins
-
Screw drivers
Pulled oven away from cabinet area
Unplugged oven from wall outlet
Removed screws to free top panel from back of oven
Removed screws to free lower panel from back of oven
Probe backing was now exposed
Unplugged probe from connector
Removed one screw from probe housing
Twisted probe housing counterclock ... Read more wise then pulled probe out
Reversed the process to install probe
Plugged probe into connector
Reversed the panel removal process
Plugged oven back in to wall outlet
Turned on oven and tested with no further issue
Unplugged oven from wall outlet
Removed screws to free top panel from back of oven
Removed screws to free lower panel from back of oven
Probe backing was now exposed
Unplugged probe from connector
Removed one screw from probe housing
Twisted probe housing counterclock ... Read more wise then pulled probe out
Reversed the process to install probe
Plugged probe into connector
Reversed the panel removal process
Plugged oven back in to wall outlet
Turned on oven and tested with no further issue
Read less
Was this helpful?
Thank you for voting!