- Home
- GLGF377ABD
- Instructions
GLGF377ABD Frigidaire Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Oven wouldn't heat
2 of 4 people
found this instruction helpful.
-
M. Nicole from La Mirada, CA
- Really Easy
- Less than 15 mins
-
Screw drivers
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Then I reattached the new piece. It was the easiest thing ever and i'm a woman!
Was this helpful?
Thank you for voting!
oven wont start
1 person
found this instruction helpful.
-
ismael from perth amboy, NJ
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires....install new element and woalla.........save thangsguivingday thanks to part select .com..........
Was this helpful?
Thank you for voting!
originaldrawer guide was cruched out of useable shape
1 person
found this instruction helpful.
-
Fred from Ocala, FL
- Really Easy
- Less than 15 mins
-
Pliers
first thing was to remove the crushed guide with pliers and a twist it was out. to install the new one islipped one side into the slot and took pliers and applied pressure on the lower glide into the slot; it was done presto. works like new. thanks,
Fred . it was so reasonable i got a spare.
Fred . it was so reasonable i got a spare.
Was this helpful?
Thank you for voting!
Oven wouldn't light off
1 person
found this instruction helpful.
-
Mickey from Fallbrook, CA
- Really Easy
- Less than 15 mins
-
Screw drivers
First I removed the two screws that held the element in place. I then pulled the element out about 3 inches and disconnected the two wires nuts, (from last repair) installed new igniter. Not rocket science here.
Was this helpful?
Thank you for voting!
oven would not lite
1 person
found this instruction helpful.
-
david from canastota, NY
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers, Wrench (Adjustable)
took of bottom pan and pan above the gas flame off and the igniter off , cut the two wires. replaced the igniter hooked the wires togther, replaced both pans. turned the oven on and it lite
Was this helpful?
Thank you for voting!
over draw was off track
1 person
found this instruction helpful.
-
Frances from Hauppauge, NY
- Really Easy
- Less than 15 mins
the part snapped on the side of the track, now the draw is not sitting on the floor and opens and closes like new.
Was this helpful?
Thank you for voting!
One guide was missing and the other was broken
1 person
found this instruction helpful.
-
Don from WEST UNION, OH
- Really Easy
- Less than 15 mins
Read the instructions provided and simply installed the guides. Total time was less than 5 min.
Was this helpful?
Thank you for voting!
Needed an additional rack
1 person
found this instruction helpful.
-
Gary from Darragh, PA
- Really Easy
- Less than 15 mins
Open the door and slide in the new rack.
Was this helpful?
Thank you for voting!
Oven Would Not Light
1 person
found this instruction helpful.
-
Michael from Houston, TX
- Really Easy
- 15 - 30 mins
-
Nutdriver
Removed broiler pan drawer,removed two screws on element unplugged wires,installed new one. ,Tried oven, works like it did when new. It couldn't have been easier,plus I saved a bunch of money thank you partselect mike m.
Was this helpful?
Thank you for voting!
guide was broken
1 person
found this instruction helpful.
-
Marvin from MONTANA CITY, MT
- Very Easy
- Less than 15 mins
-
Screw drivers
Used a slot screwdriver to pry the old guide...clipped the new guide into its place.
Was this helpful?
Thank you for voting!
OVEN WOULD NOT COME ON
1 person
found this instruction helpful.
-
david from SLIDELL, LA
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
CUT THE WIRES ON OLD IGNITER AND WIRE NUT THE WIRES OF THE NEW IGNITER TO WHERE I CUT THE OLD ONE OFF.
Was this helpful?
Thank you for voting!
oven would not lite
1 person
found this instruction helpful.
-
Walter from Danville, IL
- Easy
- 15 - 30 mins
-
Nutdriver
First i removed the broiler door and then I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and cut the two wires. I strip the ends ,connected the new unit with ceramic nuts that was provided an reconnected the unit. all was done in less than 30 min. EASY!!! plug the stove back in and
... Read more
WORKED PERFECTLY. note i receive the unit the same day it shipped....WOW
Read less
Was this helpful?
Thank you for voting!
replaced oven igniter
1 person
found this instruction helpful.
-
Gary from Waco, TX
- Easy
- 15 - 30 mins
-
Screw drivers
Removed racks,oven bottom(2 screws) and heat deflecter. Slide heat sleeves 10 inches away from old igniter. Cut wires one inch longer than the length of the heat sleeves, from the old igniter. Cut the new wires to match old wire length. Replace old igniter. Slide sleeves up to new igniter. Wire nut ends-done deal. It was hard working ove
... Read more
r the oven door,but I am old. Good luck
Read less
Was this helpful?
Thank you for voting!
Oven would not heat up
1 person
found this instruction helpful.
-
Dean from Tupper Lake, NY
- Easy
- 15 - 30 mins
-
Screw drivers
First I removed the two screws that held the element in place.I then pulled the element out and cut the wires.I used wire nuts to put the new wirers on and put it back in place with the two screws.I tried it and it worked perfect.
Was this helpful?
Thank you for voting!
Oven would not light and gas would not come through.
1 person
found this instruction helpful.
-
Jesse from Haines City, FL
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
I unplugged the stove then pulled the disconnected the wires that controled the igniter. I took the two screws off that held the igniter to the pilot port. I hand to cut the wires on the new igniter to some-what match the lenght of the broken igniter. Then I cut the connectors from the old part and used the fire resistant wire nutes tha
... Read more
t where included with the new igniter and connected it all. Put all the screws in tight, double checked every thing. Finally I plugged it in and it was working.
Read less
Was this helpful?
Thank you for voting!