EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

GLER642AS3 Frigidaire Dryer - Instructions

All Instructions for the GLER642AS3
91 - 105 of 568

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
door handle broke off a the handle
4 of 4 people found this instruction helpful.
  • John from SARATOGA SPGS, NY
  • Really Easy
  • Less than 15 mins
used a putty knife to press the clips away from the door and lift the assembly away out of the door. Used the putty knife to push the clip over the lip and snap the new handle into place
Was this helpful?
Thank you for voting!
fan cage came undone from motor
4 of 4 people found this instruction helpful.
  • Christopher from DENVER, PA
  • Really Easy
  • Less than 15 mins
The new motor from parts select was not correct. The new motor is a bolt on. The original motor was a press on. Had to return at a cost of 42.00 dollars. Had to buy a new dryer.
Was this helpful?
Thank you for voting!
Needed New Dryer Knob
4 of 4 people found this instruction helpful.
  • Teri from Port Charlotte, FL
  • Really Easy
  • Less than 15 mins
Put new knob on used no tools very easy!! Knob took 2 days to get fast service
Was this helpful?
Thank you for voting!
female part of door clasp broke
5 of 7 people found this instruction helpful.
  • Tammy from St. Peters, MO
  • Really Easy
  • Less than 15 mins
All I did was push the new part into the machine! So easy!
Was this helpful?
Thank you for voting!
Dryer was getting very hot
9 of 19 people found this instruction helpful.
  • marjorie from Cary, NC
  • Difficult
  • More than 2 hours
  • Screw drivers, Wrench set
I watched videos so I would know what I was doing. Well No, My thermostat was in the front of the dryer. But after a little blood and sweat, and I am not kidding, I got the front off. I ordered my new part. Finally got it in Spent $40.00 and it still doesn't work. I know it was the right part. I checked all the trouble shooting web site. That was the only thing they said it would be. Friends advice tell me it is the brains of the thing and I need a new one. Well not 2 weeks before Christmas. Thanks for asking. Single hard working mom.
Was this helpful?
Thank you for voting!
Screeching noise under load
4 of 4 people found this instruction helpful.
  • John from WESTLAKE, OH
  • Easy
  • 1- 2 hours
  • Nutdriver, Screw drivers
I basically followed the video instructions on your website. Pretty simple but ran into an issue pre-threading the 3 self taping screws into the spindle bearing. The screws provided were blunt on the end and did not tap easily at all. I used the existing screws that were much more "sharp" and worked much better. Also, the new screws were Philips drive and due to the amount of torque trying to self tap nearly stripped them out. The old sharper screws were square drive which had a better bite. So basically, I used the old screws to self tap and then used the new screws for the final installation.
It took a long time to clean all the lint out from the inside of the dryer. The motor was completely embedded with lint and animal hair. You may want to suggest that a good cleaning may be needed so bring a shop vac...and also something to carefully pick the lint balls out from around the motor armature and bearing area. Overall the video instructions were really a big help!
Was this helpful?
Thank you for voting!
My lent screen broke on my dryer
4 of 5 people found this instruction helpful.
  • Mary from Garland, NC
  • Really Easy
  • Less than 15 mins
  • Pliers
I remove the old lint filter and just put the new one in.
Was this helpful?
Thank you for voting!
door catch wasn't working and screws in door were loose.
12 of 29 people found this instruction helpful.
  • NICOLE from WEST JORDAN, UT
  • Really Easy
  • Less than 15 mins
  • Screw drivers
popped the catch in existing hole and replaced the screws
Other Parts Used:
Was this helpful?
Thank you for voting!
Knob needed replaced.
4 of 5 people found this instruction helpful.
  • Sharon from Moses Lake, WA
  • Really Easy
  • Less than 15 mins
I ordered a new knob on 12/22 and received it 12/27. Put in place of the broken knob, all fixed! ! ! All the appliances in my home are Frigidaire. I bought medium priced machines. W/D are about 7 years old. Dishwasher is about 5 years old. Fridge and stove are about 3 years old. They have all served me well and when they need replaced, I will shop for Frigidaires.
Was this helpful?
Thank you for voting!
Cloths not drying
5 of 8 people found this instruction helpful.
  • keith from ELLENVILLE, NY
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers, Socket set
Removed the back panel and the exhaust hose.removed the heater element and changed the thermostat wire was melted cut damaged part of wire soldered and rapped with black electrical tap
Was this helpful?
Thank you for voting!
Squeaking noises (very high pitch)
5 of 8 people found this instruction helpful.
  • Bruce from Liberty, TX
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
Replace rear bearing, found Exhust tube seal broken. Went ahead and replaced Drum belt & Idler arm assembly. Works like New !
Was this helpful?
Thank you for voting!
The timer would not shut off.
4 of 5 people found this instruction helpful.
  • David from Worthington, MN
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
Removed back of the control panel. Removed 2 screws unplugged the wires. Plugged wires into the new timer, put the back cover on. Worked great.
The repair man was going to charge us twice the cost of the part ($150) plus labor. He even recommended buying a new dryer rather then putting the money into fixing this one!
Was this helpful?
Thank you for voting!
dryer had no heat and stopped turning
5 of 8 people found this instruction helpful.
  • Eric from Spicewood, TX
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Screw drivers
i first looked up the diagram for this model and checked for the best way to take the front cover off the dryer. after removing the front cover i start looking for the wires that connect the door switch and remove the wires. the front cover also supports the weight of the drum, so carefully pull the cover until the drum comes loose. at th is point you can visually see the parts of the parts that make up the workings of the dryer. i first noticed the drum was coming out with the front cover at this time i knew the rear drum assembly was broke. i then took the belt loose from tension pulley and slid it off the drum and removed both from the cabinet. after the drum was removed i also noticed the heating was broken in several places. i removed four screws from the heating element assembly and also removed two wire that were connected to the element. with all pieces removed i checked the thermal switches, there are three switches, one on the heating element, one on the vent side and one on the back panel of the cabinet. i then installed the rear drum assembly and the heating element assembly and connected the wires. i then slid the drum almost all the in place and put the new belt around the drum and dropped the rear drum into the bracket that supports the rear drum then run the belt around the tension pulley and around the motor pulley. i then placed the front panel back in place and connected the wires for the door switch and lifted the drum assembly up just enough to insert the front panel door support into the drum and placed the clips in place, checked all connections twice and connected power back to the unit and turned on and run it through all its settings.
Was this helpful?
Thank you for voting!
heater element was broken
5 of 8 people found this instruction helpful.
  • eufemio from deltona, FL
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
I removed dryer exhaust hose.unsnapped top cover the clips are in front and exposed inside of dryer,remove 2 screws on inside of front cover and set aside. remove lower cover in back and push belt extender until belt is loose remove 3 screws on inside of tumbler. remove tumbler out the front of dryer be careful not to damage belt set asid e remove ball plate by pulling up and out it will unsnap. Now remove 2 sets of wires that are connected to heater element plate remove 4 screws holding element plate in place. Since dryer was all exposed I cleaned everything out with a wet vac put back together following instructions in reverse. Good luck
Was this helpful?
Thank you for voting!
The drier was "screeching"
9 of 9 people found this instruction helpful.
  • Michel from CHICAGO, IL
  • A Bit Difficult
  • 1- 2 hours
  • Pliers, Screw drivers
First of all, the folks at Part Select have been terrific. I balled up my address and they were great in correcting my error and getting the parts promptly to me. They provide directions with the parts. And You Tube, is a wealth of information too. The process is to remove the drum and replace the nylon busihing that supports the drum at the back of the machine. Getting it out was no sweat. Getting the drum back in was a bit more challenging single handed. If I was going to make any suggestion it would be this is a good project for two sets of hands with the second set needed for about ten minutes. The You Tube video I watched said putting the front cover with the drum attached to the back of the unit would be the challenge and they were right. Otherwise, super easy and the results are it's back to "new" condition. Thanks again to Part Select!
Was this helpful?
Thank you for voting!
All Instructions for the GLER642AS3
91 - 105 of 568