GLEFS79DCB Frigidaire Range - Instructions

I watched you vedio and done just as the vedio told me how to change the switch. When I got the switch on pluged it in turned it on and every thing work great. thank you very much.

watched the veido first then un pluged the stove then i took out 6 screws and 2 from the switch and reversed every thing

Easy to put in but i droped a screw to hold the element. had to pull another screw to fix it

Replaced the control I got from you , even though it was a little different the lugs matched up and works great.

The part i replaced was very easy.I pulled the stove away from the wall and took the back pannel off. I then unpluged the electrical strip from the unit.There are two nuts holding the unit in place one at each end,there are also five wires on the right side of the unit you will have to mark them before you disconnect them. Then carefully ... Read more peal the face off the old unit and reinstall on the one. Put the new unit in place, plugin the electrical strip,the five wires,reinstall the back cover,plugin your stove and your done. All this took about twenty minutes start to finish.

Pull out stove. Unplug power. Remove four screws on each corner and loosen one screw in the middle. Remove back panel. Locate and unplug sensor connector. Remove one screw from sensor plate. Turn the sensor 45 degrees and pull sensor out from the rear. Connector received had the incorrect plug and terminals so it was necessaary to sp ... Read more lice the connector from the one removed to the one received. Cut and splice wires as necessary. Install sensor, install back panel, plug in electrical power, push stove back into position. I used a temperature gauge to check temperature after stove was in position. In my case the temperature had to be adjusted which is a keyboard function on this unit.

Screwed up by not shutting breaker. Shorted out 3 switches. Thought i could get away without shutting breaker that was a costly error. No problem replacing the 3 switches and element switch. Took about 1/2 an hour.Always shut breaker before doing any electrical repairs.

Took back cover off 2 screws held the switch then moved wires one at a time from old switch to the new one put everything back plugged in stove everything worked

Checked the burner and no power to heat the burner. removed the old switch and put on the new one.

open door,throw the door latches at the hinges and remove door. Take the out of the outer panel so you can separate the glasses. remove clip that hold the outer glass in place. I ordered a replacement glass as I never thought that it would come clean it looked so bad, but it cleaned up like new so I now have a spare glass for my oven door ... Read more . Just reverse the way you take it apart to put it back together.

Cut the range power. Removed the top rear panel. Removed the two burner switch screws. Pulled one wire at a time off the old switch and put it on the new switch. Since the terminal location did not match, it was critical to notice the terminal designation on the old and match it to the new switch. Ex., H1 to H1; H2 to H2. Voila! It worked ... Read more the first time.

Confirm the problem and check electrical diagram to see if there was any other circuit in the syatem that could cause the burner to stay on , remove back cover and inspect switch contacts, found them burnt , look up parts for the model number and replace it.

Took door apart, went online to partselect, ordered new glass, and put it back together. Oven looks like new. Makes sense to order the isolation as well when you do the repair

First, I disconnected the electrical power by pulling apart the plug behind the range. Next, I removed the screws holding the service plate on back of the top panel.I removed the switch knob by gently pulling it from the stem. Underneath I found 2 screws holding the switch in the panel. I removed these with a phillips screwdriver.I was ab ... Read more le to pull the entire switch out to the rear leaving all wires attached.The new switch looked different from the original and the wires were configured differently but the wires were clearly marked. By removing one at a time and placing it on the new switch to the corresponding marking,it was a simple matter to wire the switch.I reinstalled the switch in the panel,put back in the screws to hold the switch, slid the knob back on the stem, reinstalled the rear panel,and plugged the power cord back in.The switch worked perfectly.

Followed video instructions on your web site.Removing one wire at a time as suggested simplified installation.Somehow i lost burner lens indicator.Ordered it from your website cost $3.84 plus shipping recieved in one day. GREAT SERVICE