EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

GLEF387FCC Frigidaire Range - Instructions

All Instructions for the GLEF387FCC
121 - 135 of 227

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Convection fan making noise
0 of 1 people found this instruction helpful.
  • Willis from Friendsville, TN
  • Easy
  • 15 - 30 mins
  • Screw drivers, Wrench (Adjustable)
Removed old fan and replaced with new fan. To replace fan, the over interior fan blade was removed, then the two slip on wires were removed from the old fan motor, then the three screws securing the old fan motor were removed. The process was reversed to install replacement fan
Was this helpful?
Thank you for voting!
Broil Element shorted out
0 of 1 people found this instruction helpful.
  • Frederick from Pompano Beach, FL
  • Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
I unplugged the Stove/Oven electrical cord from the wall, then removed the oven door by unlocking the door brackets with a flat head screw driver then closing the door to the last position before it closes and removing the door from the stove (found instructions on YouTube - very easy, which is optional), then removed the oven racks. Rem oving the door made it a lot easier to access the broil element and element support bracket screws using a socket wrench. I removed the screws from the rear cover on the back of the stove with a socket wrench to access and disconnect the broil element wires with my hand (pliers if needed). I removed the old broil element and inserted and reconnected the new broil element wires, then re-installed the rear cover. I tightened the broil element in place then re-installed the element support bracket and screws, replaced the oven racks, re-installed the oven door and plugged the stove into the wall. This took about twenty minutes and the broil element is working fine.
Was this helpful?
Thank you for voting!
My oven door seal was worn and did not seat properly. It leaked heat.The infinite burner was not warming in the low heat positions
1 of 4 people found this instruction helpful.
  • Frank from PALM COAST, FL
  • A Bit Difficult
  • 1- 2 hours
  • Nutdriver, Screw drivers
I followed two very good videos on how to do the repairs. It took longer to clean all the disassembled parts and the glass than it did to actually do the repair.
A word of caution: Be sure to lock the door hinges in the open position before you lift out the door. They must be locked open to put the door back on. It's difficult to loc k them open once the door is removed. Also when you replace the screws get them all aligned in the holes before you lock everything down.
The infinite burner switch was pretty easy to replace but watch out for sheet metal cuts when you are removing the back of the stove. I recommend gloves. My stove has a 12 inch infinite burner, but the parts list only mentions a 10 inch burner. Before I ordered it, I had to call the company to verify that it could be used for the 12 inch burner as well.
Was this helpful?
Thank you for voting!
Cracked inside glass
0 of 2 people found this instruction helpful.
  • patti from Greer, SC
  • A Bit Difficult
  • 1- 2 hours
  • Screw drivers
I actually watched Youtube while I was changing it. This video was not actually the same make up of my oven, even though the I typed in the model number. I manage to figure it any with the steps anyway. It was harder then I expected but not horrible. I think I did pretty well for a women. Patti
Was this helpful?
Thank you for voting!
Control will not work - only clock blinks
0 of 4 people found this instruction helpful.
  • Sue from Lampasas, TX
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers
Took 3 panels off to get to the electric block. Replaced electrical block and put it back together. Still no change.
Was this helpful?
Thank you for voting!
Broken globe in oven and burnt out light bulb
0 of 5 people found this instruction helpful.
  • Sharon from Foley, AL
  • Really Easy
  • Less than 15 mins
Easy as 1-2-3
Other Parts Used:
Was this helpful?
Thank you for voting!
lost a rack?
  • Melanie from Reading, PA
  • Really Easy
  • Less than 15 mins
After removing an oven rack to make room for the thanksgiving turkey roaster, I have NO IDEA, where I might have stowed it away! After searching every cabinet and every closet I realized I needed to do something quick for our annual christmas cookie marathon that would begin on Sunday. It was so easy to order the part, it arrived the next day, and we baked for 5 hours using the 3 racks in the convection oven. Dozens of cookies later... Thank you Parts Select!
Was this helpful?
Thank you for voting!
Oven not heating up properly
  • Larry from Jordan, AR
  • Really Easy
  • Less than 15 mins
  • Nutdriver
I removed back cover and replaced the probe. The troubleshooting info indicated this is the problem 99% of the time. Guess what, it did not help! Further checks indicate that broil element may be out. Am going to resistance check and order if that is the problem.
Was this helpful?
Thank you for voting!
Switch was Sparking
  • Susan from Hillsboro, OR
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
So simple....removed back panel, removed knob from front of range and removed 2 screws holding the knob in. Used needle nose pliers to pull wires off existing switch, placed wires in identical spots on new switch. Put switch post through front of range and put the 2 screws back in and the knob on. Finished and ready to go in less than 1 0 minutes. No more sparking....
Was this helpful?
Thank you for voting!
When turning the switch on for the large eye I could hear an electrical short behind the switch.
  • Kent from McHenry, MS
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
Initially we realized there was a problem while cooking with the large eyes and we began hearing an electrical short behind the control switch. I unplugged the power from the oven/cooktop and removed the back panel where I could visually see soot on the switches where it was shorted. Careful while choosing your part from the diagram on P artselect.com. For the model FEF336ECJ, atleast for my oven, the eye switches were reversed and I ordered the small eye's switches! Luckily they have an outstanding customer support and immediately mailed out the new parts and a label to send the wrong parts back. Changing the parts out was very simple. Pull the oven out and UNPLUG IT from any electrical outlet. Remove the back panel. Double check from the label on the front of the control panel that you are working with the correct switch, and before removing the current switch, remove the wires one by one and place them on the new part to make sure you don't misplace these wires. Once the wires are connected to the new part, pull the plastic knob off of the old switch to reveal the screws on front of the panel. Place the new switch where the old one came from and fasten the screws back in place. Replace the knob, replace the back panel(for safety) and test the new switch before you push the oven back into place. If you can turn a screw driver, move the oven, and unplug the power, this easy do it yourself repair will save you possibly hundreds by not calling a repair/handyman who would absolutely love you to pay out the nose for such an easy task.
Was this helpful?
Thank you for voting!
Burner would stay on high when switch was on simmer
  • Dennis from Corpus Christi, TX
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Disconnected power first. Removed 4 screws on the back of the range, pulled the knob off of the switch, removed 2 small screws on the switch(on the front , under the knob) pulled off the 4 wires with spade connections on the switch. Put wires on the new switch, put in 2 screws on new switch, pushed knob on switch, replaced back cover and tested the new switch. Works great. Took less than 10 mins.
Was this helpful?
Thank you for voting!
element light staying lit
  • Russell from Glenmoore, PA
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
Screwed up by not shutting breaker. Shorted out 3 switches. Thought i could get away without shutting breaker that was a costly error. No problem replacing the 3 switches and element switch. Took about 1/2 an hour.Always shut breaker before doing any electrical repairs.
Was this helpful?
Thank you for voting!
really bad ugly streaks inside of glass
  • John from Hemet, CA
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
open door,throw the door latches at the hinges and remove door. Take the out of the outer panel so you can separate the glasses. remove clip that hold the outer glass in place. I ordered a replacement glass as I never thought that it would come clean it looked so bad, but it cleaned up like new so I now have a spare glass for my oven door . Just reverse the way you take it apart to put it back together.
Was this helpful?
Thank you for voting!
oven took too long to heat up
  • JAONNE from GAFILED, NJ
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
un bolted the 6 nut driver heads found probe wire un pluged it 1/4 turn from lock it was in and pull out replace slide in new probe 1/4 turn to lock it in place replace nut driver self tappers and test simple!!
Was this helpful?
Thank you for voting!
the stove eye would go to high and stay
  • ronnie from cana, VA
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
watched the veido first then un pluged the stove then i took out 6 screws and 2 from the switch and reversed every thing
Was this helpful?
Thank you for voting!
All Instructions for the GLEF387FCC
121 - 135 of 227